LT8610AEMSE#TRPBF
Product Specifications
LT8610AEMSE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT8610AEMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT8610AEMSE#TRPBF: 42 V In, 3.5 A Out, and a 30 ns Minimum On-Time That Opens the High Ratio
The LT8610AEMSE#TRPBF is a monolithic synchronous step-down converter that takes 3.4 V to 42 V in, delivers 3.5 A, and does it with 2.5 uA of quiescent current while regulating 12 V to 3.3 V. It is the A version of the LT8610 family, so compared with the original part it raises the output current from 2.5 A to 3.5 A and cuts the minimum switch-on time from 50 ns to 30 ns, which is the number that matters for high input to low output ratios. The E suffix is the temperature grade: the part is guaranteed to meet its specifications from 0 to plus 125 degrees junction, with the minus 40 end assured by characterisation and correlation rather than by test, and the I grade is the version guaranteed across the whole minus 40 to plus 125 range.
Minimum on-time is what makes 42 V to 3.3 V possible
A buck converter's duty cycle is the output voltage divided by the input voltage, so 42 V to 3.3 V is 7.9 percent. At a 2.2 MHz switching frequency that is 35.7 ns of on-time, and with a 30 ns minimum the converter can hold the ratio with about 5 ns of margin, which is why the A version exists: the 50 ns part cannot. At 2 MHz and 42 V in the same conversion is 39 ns, which clears 30 ns comfortably, and at 1 MHz it is 79 ns. The practical reading is that the highest switching frequency is available only at the lower input voltages, and a system that needs both 42 V input and 2.2 MHz has to accept a lower output voltage or a larger inductor.
Quiescent current, burst mode and the divider that spoils it
The 2.5 uA figure is the current drawn from the input while regulating 12 V to 3.3 V with no load, and it is made of two parts: 1.7 uA of quiescent current for the converter itself and about 0.8 uA contributed by the feedback divider reflected through the conversion ratio. A higher value divider lowers the second term and a lower value divider raises it, so the 2.5 uA is a property of the recommended divider and not of the silicon alone. Between bursts the part shuts down its control circuitry and the input current falls to 1.7 uA, and the output ripple in burst mode stays below 10 mV peak to peak, which is what allows the part to sit on a standby rail without a second linear regulator.
| Parameter | Value on this order code | What it decides |
|---|---|---|
| Input range | 3.4 V to 42 V | Automotive and 24 V industrial rails directly |
| Output current | 3.5 A maximum | The A version, the original LT8610 is 2.5 A |
| Minimum on-time | 30 ns | 42 V to 3.3 V at 2.2 MHz needs 35.7 ns |
| Quiescent current | 2.5 uA regulating 12 V to 3.3 V | 1.7 uA part plus 0.8 uA divider |
| Burst ripple | Below 10 mV peak to peak | Standby rail without a second regulator |
| Switching frequency | 200 kHz to 2.2 MHz, adjustable or synchronised | Frequency is a ratio and loss decision |
| Reference | 0.97 V | Sets the output floor and the divider |
| Temperature grade | E, guaranteed 0 to plus 125 degrees junction | I grade is tested across minus 40 to plus 125 |
| Package | 16-lead MSOP with exposed pad | The pad is the thermal path, not a mechanical detail |
Efficiency, dropout and the two ways a rail fails
The family runs 96 percent at 1 A with 5 V out from 12 V in, and the A version keeps that behaviour at its higher current. Dropout is 200 mV at 1 A, which matters for a rail that has to stay in regulation while the input sags, and it is the reason a 5 V output from a 5.5 V input is a short duration requirement rather than a continuous one. The other failure mode is light load: in forced continuous mode the part keeps switching and the efficiency collapses at microamp loads, while in burst mode it stays high and the ripple stays bounded, so the mode selection is a system decision and not a detail of the application circuit.
Where the part belongs
Automotive and industrial supplies, always-on standby rails, 24 V systems that need a 3.3 V or 5 V logic rail and instrumentation that has to work from a wide input are the intended sockets. Where the input can exceed 42 V a different converter is needed, and where the load current is above 3.5 A the next part in the family is the answer rather than a second converter in parallel. The ADI part second source page sets out what a substitute has to match, the pin to pin cross reference covers the package question, and the one stop BOM sourcing page covers the converter, its inductor and its capacitors on one order.