Contact Us

LT3090MPMSE#TRPBF

Brand: Analog Devices
Analog Devices LT3090MPMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3090MPMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3090MPMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3090MPMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3090MPMSE#TRPBF: the 150 C negative regulator in a 12-lead MSOP

The LT3090MPMSE#TRPBF is the widest temperature grade of the LT3090, a 600 mA negative low dropout regulator that takes -1.5 V to -36 V on the input and holds any output between 0 V and -32 V. The MP code is rated -55 C to 150 C at the junction and is supplied in the 12-lead MSOP on tape and reel. One resistor from SET to ground sets the output, because the SET pin sources a fixed 50 uA with 1 percent initial accuracy, and a second resistor on the ILIM pin sets the current limit. Both the positive and the negative side of the load current can be monitored through the IMONP and IMONN pins.

Published values

ParameterValue
Input voltage-1.5 V at 100 mA, -1.9 V at 600 mA, up to -36 V
Output voltage0 V to -32 V, one resistor on SET
Output current600 mA, programmable limit
SET pin current50 uA, 49 to 51 uA over the full range
Dropout voltage300 mV typical at 600 mA, 450 mV maximum
GND pin current1 mA at no load, 2.6 mA at 100 mA, 11.5 mA at 600 mA
Output noise18 uV RMS, 10 Hz to 100 kHz
Ripple rejection85 dB at 120 Hz, 50 dB at 10 kHz, 20 dB at 1 MHz
Load regulation1.2 mV from 1 mA to 600 mA
Shutdown current4.5 uA typical
Thermal resistance34 C/W junction to ambient, 5.5 C/W to case
Package and grade12-lead MSOP, -55 C to 150 C, tape and reel

What the MP window actually buys

Most negative rails on an industrial board are specified at -40 C to 85 C ambient, so a 125 C part looks generous. The MP code matters in two other cases: equipment that is certified down to -55 C, and boards where the regulator sits in still air next to a transformer or a bridge rectifier and the local ambient near the part is 15 to 25 C above the cabinet figure. The 25 C of extra junction headroom converts into a wider acceptable ambient for a given dissipation. At 1.38 W the rise through a 34 C/W MSOP is about 47 C, so a 125 C part runs out of margin at roughly 78 C ambient while the 150 C part holds to about 103 C.

Working from the SET pin instead of a divider

Because the SET pin is a current source rather than a voltage reference input, the output equation is a single multiplication: output equals 50 uA times the SET resistor. A 66.5 kOhm resistor gives -3.325 V, a 100 kOhm gives -5 V, a 240 kOhm gives -12 V. The attraction for a buyer is that the same resistor value produces the same rail on every board in a family, and the tolerance of the rail is the 1 percent initial accuracy of the current plus the resistor tolerance and not a divider ratio. The IMONP pin then sources and the IMONN pin sinks a scaled copy of the load current, so a single sense resistor to ground on either pin gives a positive voltage for an ADC even though the rail itself is below ground.

Where the 600 mA goes at temperature

The part is a linear regulator bolted to a negative rail, so the dissipation is the input to output differential times the load current plus the quiescent contribution. A -5.5 V input feeding -3.3 V at 600 mA is 1.32 W in the pass element and another 63 mW in the quiescent path, which lands at 47 C of rise on the MSOP body with 2500 square millimetres of copper. Doubling the copper area does not help much at this package size, so the practical levers are a lower input differential, a smaller load current, or two devices in parallel. The LT3090 is built for that last option: outputs can be tied directly without ballast resistors, and each device carries its own current limit, which is why the same order code appears on rails that need 1.2 A from two parts.

Order code and replacement risk

The MPMSE code is tape and reel; the same die is available in the 10-lead 3 mm DFN as MPDD and in the E, I and H grades of both bodies. When this line is short, the substitution that usually works is the same body in another grade, and the substitution that fails is a positive regulator picked by current rating alone, because the pin functions are mirrored around ground. Files that carry several ADI rails benefit from keeping the negative family on one line item, which is what the power management cross reference is built for. Consolidated buying across those lines is handled on the one stop BOM sourcing page, and current scheduling for the MSOP body is on the lead time page.