Contact Us

LT3088IST#TRPBF

Brand: Analog Devices
Analog Devices LT3088IST#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3088IST#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3088IST#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3088IST#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3088IST#TRPBF: 800 mA industrial regulator, SOT-223, the LT1117 upgrade path

The LT3088IST#TRPBF is the industrial grade of the 800 mA single resistor regulator in the 3-lead SOT-223, tape and reel, specified from -40 C to 125 C. It takes 1.2 V to 36 V in and delivers 0 V to 34.5 V out with one resistor to the SET pin, using a 50 uA reference with 1 percent initial accuracy. Noise is 27 uV RMS, typical load regulation is under 1 mV and does not change with the output voltage, line regulation is 0.001 percent per volt, and the part is stable with or without input and output capacitors.

Published values

ParameterValue
Input voltage1.2 V to 36 V
Output voltage0 V to 34.5 V, one resistor
Output current800 mA
SET pin current50 uA, 1 percent
Output noise27 uV RMS
Load regulationunder 1 mV typical
Line regulation0.001 percent per volt
Capacitorsstable with or without input and output capacitance
Protectionreverse battery, reverse current, current limit, thermal limit
Package3-lead SOT-223, tape and reel
Temperature range-40 C to 125 C

Why engineers move off the LT1117

The LT1117 family is a fixed and adjustable three terminal regulator that has been on boards for decades, and its limits are well known: it needs a tantalum or electrolytic output capacitor with some ESR to stay stable, its quiescent current climbs under light load, and the reference is ground referred so the output cannot go below 1.25 V. The LT3088 is offered as a pin compatible upgrade, with a current source reference instead of a ground referred one, so the output can go to zero, the load regulation does not depend on the programmed voltage, and the part is stable with ceramic capacitors or with none at all. For a buyer this is the classic case where a drop in part changes the passive list, and the ceramic capacitors that were forbidden with the old device become the default.

No output capacitor at all

Stability without an output capacitor is unusual and it simplifies a board that has to work at the end of a cable. Without a local capacitor the regulator reacts to a load step by moving its own output, and the cable inductance is in the loop, so the transient response is slower but the loop does not ring. In a build where the load is on another board, that can be better than a capacitor that resonates with the cable. The trade is ripple rejection at high frequency, which falls when the output capacitor is removed, so the choice should be made from the load's tolerance rather than from habit.

Reverse current in a shared bus

When several boards share a 24 V bus and one board loses its input, the other boards hold the bus up and the regulator on the failed board sees its output above its input. On an ordinary three terminal regulator that condition pulls current backwards through the pass element and often destroys it. This family withstands reverse input and reverse output to input voltages without reverse current flow, which is why it appears in redundant and hot swap supplies. Buyers writing a specification for a shared bus should state that requirement explicitly, because it is not universal across 800 mA regulators.

Ordering notes

IST is the industrial grade in SOT-223 with tape and reel. The E grade shares the same temperature window with a different qualification package, H extends to 150 C and MP starts at -55 C. The DD-Pak and 8-lead DFN bodies carry the same electrical table. Our power management cross reference keeps the grades and bodies in one view, the one stop BOM sourcing page covers grouping this part with the rest of a power section, and the cost page sets out the volume levers.