Contact Us

LT3086HFE#TRPBF

Brand: Analog Devices
Analog Devices LT3086HFE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3086HFE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3086HFE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3086HFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3086HFE#TRPBF: the 150 C junction version of the 2.1 A regulator

The LT3086HFE#TRPBF is the high temperature grade of the 40 V, 2.1 A regulator in the 16-lead TSSOP, rated -40 C to 150 C at the junction and supplied on tape and reel. It keeps the full function set of the family: 0.4 V to 32 V output from one resistor, 1.4 V to 40 V input, plus or minus 2 percent accuracy, current and temperature monitors, a power good flag with a programmable threshold and cable drop compensation. On this die the H grade is the one that buys hot end headroom, and it costs less than a switch to a different package would.

Published values

ParameterValue
Input voltage1.4 V to 40 V
Output voltage0.4 V to 32 V
Output current2.1 A
Reference at 25 C400 mV, 396 to 404 mV
Reference above 125 C388 to 408 mV, H grade column
Dropout at 2.1 A330 mV typical, 415 mV maximum
Current monitorIMON equals load current divided by 1000
Output noise40 uV RMS, 10 Hz to 100 kHz at 5 V out
Thermal resistance25 C/W on 2500 square millimetres, 33 C/W at 100 square millimetres
Package and grade16-lead TSSOP, -40 C to 150 C, tape and reel

Where the extra 25 C is spent

A junction limit of 150 C against 125 C is 25 C of margin, and at 25 C/W that is exactly 1 W of extra dissipation. Put the other way round: at 2 W in a 70 C cabinet the junction sits near 120 C on a small copper area, which a 125 C part survives only on paper, and the H grade runs at 150 C with the same board. Boards that feed a 12 V rail from a 24 V bus at 2.1 A dissipate 25 W, which no TSSOP can carry, so the honest use of the H grade is the medium case: a few watts, a hot cabinet, and no room for a DD-Pak.

The reference window above 125 C

The electrical table has a separate column for the H grade above 125 C, and the reference moves from 396 to 404 mV at room temperature to 388 to 408 mV over the extended window. That widening is real and should be carried into the error budget for any product that runs its junction past 125 C: it is 5 percent of the setpoint at the extremes, larger than the resistor tolerance and larger than the amplifier offset. A budget built from the room temperature numbers alone will understate the error in exactly the equipment that buys this grade.

Protection behaviour when the die is already hot

With a junction limit of 150 C and a thermal monitor pin, the part can be made to fold back before it reaches shutdown. The ITEMP pin sets the current at which foldback begins, and the TEMP pin reports the die temperature to the system, so a controller can reduce a load or start a fan instead of waiting for the internal protection to act. On a 150 C part that headroom is wider but the margin to a hard shutdown is smaller, because the ambient is usually higher, so the external foldback is worth having rather than optional.

Order code and stock

HFE is the high temperature TSSOP; IFE and EFE are the standard grades of the same body, MPFE is the -55 C to 125 C version, and the DD-Pak and TO-220 forms of the same die exist for boards that can afford the copper. The TSSOP is the one that fits a dense board, which is why this grade exists at all. The lead time page carries the schedule, the ADI second source page lists the grade options, and vendor consolidation covers buying several grades of one family on a single line.