Contact Us

LT3086EFE#TRPBF

Brand: Analog Devices
Analog Devices LT3086EFE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3086EFE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3086EFE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3086EFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3086EFE#TRPBF: paralleling 2.1 A devices without ballast resistors

The LT3086EFE#TRPBF is the extended grade of the 40 V, 2.1 A regulator in the 16-lead TSSOP, on tape and reel and rated -40 C to 125 C. It carries the full family specification: 0.4 V to 32 V output from one SET resistor, 400 mV reference, 50 uA SET current, 330 mV typical dropout at 2.1 A, plus or minus 2 percent accuracy, current and temperature monitors, power good and cable drop compensation. The reason to look at this part rather than a single larger regulator is that several of them can share a load with no ballast resistors and no master control loop.

Published values

ParameterValue
Input voltage1.4 V to 40 V
Output voltage0.4 V to 32 V
Output current2.1 A per device
Dropout at 2.1 A330 mV typical
Reference400 mV, 0.1 percent line and load regulation
Current monitorIMON equals load current divided by 1000
Minimum output capacitor10 uF ceramic
Thermal resistance25 C/W on 2500 square millimetres, 28 C/W at 225 square millimetres
Package and grade16-lead TSSOP, -40 C to 125 C, tape and reel

How sharing works without ballast

Each device carries its own 50 uA reference and its own SET resistor, and the outputs are tied together. Because the reference is a current rather than a voltage, a small difference in output between two devices does not cause one to hog the load: the TRACK pin lets the devices communicate so that the SET nodes move together and the load splits within the published sharing error. The alternative, a resistor in series with each output, wastes the voltage the regulator was chosen to save. For a 4 A rail this is the difference between two parts and two parts plus two heat sources.

The thermal argument for two devices

A single TSSOP carrying 4 A is not possible, but two carrying 2 A each sit at 25 C/W apiece with the heat spread over two separate copper shapes. At a 1 V differential the pair dissipates 4.2 W in total, so each package handles 2.1 W and rises about 53 C over the surrounding copper. Spread across two locations on the board, the local hotspots are half the size, which matters in a sealed enclosure where the copper is the only path to the walls. The current monitor on each device then reports its own share, so an unbalanced pair is visible in telemetry rather than only as a hot spot.

Sequencing and the power good flag

With several devices on one rail, the power good flags can be wired together to a single sequencer input, because each flag is an open drain style output with a programmable threshold. That gives one signal for the whole rail instead of one per regulator, and the delay capacitor sets how long the flag waits after the output enters regulation. For a board that powers an FPGA and its memory from the same rail, the combined flag is the signal that releases the next stage.

Order code and stock

EFE is the extended grade TSSOP on tape and reel, IFE the industrial grade of the same body, HFE the 150 C version and MPFE the wide cold version. Every one of them can be paralleled, so a rail can grow without a new part number. The one stop BOM page covers ordering the pair plus the SET resistors on one line, the cost page covers volume pricing, and the power management cross reference maps the family against the other ADI regulators that share this pinout family.