Contact Us

LT3082EDD#TRPBF

Brand: Analog Devices
Analog Devices LT3082EDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3082EDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3082EDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3082EDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3082EDD#TRPBF: two 200 mA devices in parallel for 400 mA

The LT3082EDD#TRPBF is the extended grade of the 200 mA regulator in the 8-lead 3 mm by 3 mm DFN, on tape and reel and rated -40 C to 125 C. It has the same 10 uA SET current, the same 2.2 uF output requirement and the same internal reverse battery and reverse current protection as the rest of the family. The feature that makes this body interesting for a power rail is that the outputs can be paralleled to share a load or to spread heat, without ballast resistors.

Published values

ParameterValue
Input voltage1.2 V to 40 V
Output voltage0 V to 38.5 V
Output current200 mA per device
SET pin current10 uA, 1 percent
Load regulationUnder 1 mV typical
Line regulationUnder 0.001 percent per volt
Output noise33 uV RMS, 10 Hz to 100 kHz
Ripple rejection90 dB at 120 Hz, 20 dB at 1 MHz
Minimum load current0.5 mA
Thermal resistance25 C/W on 2500 square millimetres, 28 C/W at 1000 square millimetres
Package and grade8-lead, 3 mm by 3 mm DFN, -40 C to 125 C, tape and reel

Sharing a load between two bodies

The SET pin is a current reference, so two devices with their own resistors of the same value hold the same setpoint. Tie the outputs and both regulate to that point; any mismatch shows up as a small current difference rather than as a runaway, because the reference is a current and not a voltage divider. The result is a 400 mA rail from two 3 mm parts, each dissipating half the drop, which on a board with no room for a larger package is the practical way to double the current. The published load regulation of under 1 mV means the shared rail does not sag when one device takes more of the load.

Heat spreading with a 25 C/W body

Two devices on separate copper shapes dissipate half as much each and, more importantly, put the heat in two places. At 200 mA each with 1 V of differential the pair dissipates 400 mW and each body rises about 10 C over its own copper. A single larger part would have the same total, so the gain is in the distribution and not in the total: a small enclosure with limited copper benefits from two smaller hot spots, while a board with a good plane sees no difference at all. That is the argument to check before adding a second part number to the list.

Low output voltages without a divider

The offset between output and SET is 0.5 mV typical, so a rail of 0.9 V from a 100 kOhm SET resistor is accurate and stable. On a divider based regulator the same rail would need a low value divider that draws current continuously and adds noise. Here the SET pin draws 10 uA regardless of the setpoint, so the current in the programming resistor is the same at 0.9 V as at 20 V, and the noise contribution of the resistor is fixed by the optional SET capacitor rather than by the ratio.

Order code and stock

EDD is the extended grade DFN on tape and reel, IDD the industrial grade of the same body, EST and IST the SOT-223 versions, and ETS8 the 8-lead SOT-23. The die is common across all of them, and any two can be paralleled with the same result. The power management cross reference maps the pack forms, vendor consolidation covers keeping the family on one order, and the cost page shows the volume break for the DFN body.