Contact Us

LT3071IUFD#TRPBF

Brand: Analog Devices
Analog Devices LT3071IUFD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3071IUFD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3071IUFD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3071IUFD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3071IUFD#TRPBF: 5 A regulator with 85 mV dropout and analog margining

The LT3071IUFD#TRPBF is a 5 A low dropout linear regulator in the 28-lead 4 mm by 5 mm QFN, industrial grade, tape and reel. The output is digitally programmable from 0.8 V to 1.8 V in 50 mV steps, with an analog margining input that moves the rail over a continuous plus or minus 10 percent range for test. Dropout is 85 mV typical, noise is 25 uV RMS over 10 Hz to 100 kHz with a 0.01 uF bypass on the reference, supply rejection is 30 dB at 1 MHz, accuracy is 1 percent over line, load and temperature, and the output current monitor reports load current as one 2500th of the output.

Published values

ParameterValue
Output current5 A, parallelable for 10 A or more
Output voltage0.8 V to 1.8 V, 50 mV steps
Analog marginingplus or minus 10 percent, continuous
Dropout voltage85 mV typical
Output noise25 uV RMS, 10 Hz to 100 kHz
Supply rejection30 dB at 1 MHz
Accuracy1 percent over line, load and temperature
Current monitorIMON equal to output current divided by 2500
Output capacitor15 uF low ESR ceramic minimum
Package28-lead 4 mm by 5 mm QFN
Temperature range-40 C to 125 C, industrial grade

Built for the last centimetre before a core rail

A modern processor or FPGA takes its core voltage from a switching regulator and then needs a stage that holds the rail tight when the load steps. The LT3071 is that stage: 85 mV of dropout means the intermediate bus can sit close to the core voltage, so the loss is small even at 5 A, and the loop is fast enough that a 15 uF ceramic output covers a load step. The digital programming in 50 mV steps lets a single board support several core voltages by pin strapping, and the analog margining input moves the rail while the board is running, which is how a production test station checks the processor's margin without changing the supply.

The monitor and the tracking pin

The current monitor outputs one 2500th of the load current, so a 2.5 kohm resistor to ground gives a volt per amp, and that signal feeds a controller or an ADC for power reporting. The tracking pin drives the upstream buck converter so that the regulator's input stays near the output plus 300 mV, which holds efficiency high across the load range and keeps the linear stage from dissipating the margin. In a system with several core rails this is the difference between a 5 A linear stage that runs cool and one that needs a heatsink.

What to check before a substitution

The parts of this device that are hard to replace are the 50 mV programming resolution, the continuous margining input, the current monitor scale and the tracking function. A substitute that meets 5 A and 85 mV but lacks margining changes the test station, and one that lacks tracking changes the thermal calculation of the whole rail. The 15 uF minimum output capacitance and the 0.01 uF reference bypass are also part of the noise and stability numbers, so the passive list has to move with the device. Buyers comparing codes should hold those four items as the checklist; the power management cross reference groups the family, and the ADI second source notes list the checks in order.

Ordering

IUFD is the industrial grade in the 28-lead QFN with tape and reel; the E grade shares the -40 C to 125 C window and the MP grade covers -55 C to 125 C. The QFN has an exposed pad that is the only thermal path, so the copper under the part and the via stitching decide whether 5 A is available in an enclosure. Quotations for the QFN body follow the schedule on the lead time page.