Contact Us

LT3071EUFD#TRPBF

Brand: Analog Devices
Analog Devices LT3071EUFD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3071EUFD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3071EUFD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3071EUFD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3071EUFD#TRPBF: 5 A at 85 mV dropout with 50 mV output steps

The LT3071EUFD#TRPBF is a 5 A linear regulator in a 28-lead 4 mm by 5 mm QFN, on tape and reel and rated -40 C to 125 C at the junction. Output is selected digitally between 0.8 V and 1.8 V in 50 mV steps by three three-state pins, and an analog margining pin moves the rail continuously by plus or minus 10 percent for supply margin testing. Typical dropout is 85 mV at 5 A, output noise is 25 uV RMS, and the part is stable with 15 uF of ceramic output capacitance.

Published values

ParameterValue
Input voltageUp to 3.3 V, 0.8 V to 1.8 V output
Bias supply0.95 V to 3.0 V, above the input
Output current5 A
Dropout voltage85 mV typical at 5 A
Output setting0.8 V to 1.8 V in 50 mV steps, three logic pins
MarginingPlus or minus 10 percent, analog pin, 600 mV reference shifted
AccuracyPlus or minus 1 percent over line, load and temperature
Current monitorIMON equals load current divided by 2500
Output noise25 uV RMS, 10 Hz to 100 kHz
Rejection30 dB at 1 MHz
Minimum output capacitor15 uF ceramic
Thermal resistance30 C/W on 2500 square millimetres, 35 C/W at 100 square millimetres
Package and grade28-lead, 4 mm by 5 mm QFN, exposed pad is ground

Eighty five millivolts at five amps

The dropout figure is the reason this part exists. At 5 A and 85 mV the pass element dissipates 425 mW, which is 22 C of rise on a 2500 square millimetre shape, so a converter can deliver 1.05 V and the regulator can hold 0.96 V without the linear stage becoming the heat source. The trick is a separate BIAS pin that powers the internal circuitry from a higher rail, so the gate of the pass device can be driven above the input. The same pin is why the input range stops at 3.3 V: this is a part for the last few hundred millivolts of a low voltage rail, not for a 12 V bus.

Digitally selected output and analog margining

The three select pins set the nominal output in 50 mV increments, which is enough to cover the common core and DDR rails without a resistor divider and without a trim step in production. The margining pin then moves the reference continuously by plus or minus 10 percent, so a test fixture can sweep the rail above and below nominal while the system runs. The two functions are separate: the digital pins set where the rail sits, the analog pin moves it around that point. For a board that has to be characterised over supply tolerance, that removes the external DAC and the summing network.

The tracking pin and the upstream converter

The VIOC pin drives an upstream buck regulator so that its output stays about 300 mV above the linear regulator output. That keeps the input to output differential small at every setpoint, which is what holds the dissipation down when the rail is programmed low. For a system that changes its core voltage at run time, this is the difference between a regulator that stays cool and one that heats up whenever the rail is set to its lowest value. The pin is an output from this part, not an input, so the upstream converter has to accept a tracking reference.

Current monitor and sequencing

The IMON pin delivers one twenty five hundredth of the load current, which at 5 A is 2 mA, so a 1 kOhm resistor gives 2 V and a 500 Ohm resistor gives 1 V for a full scale reading. The enable pin threshold is ratioed to the bias supply at 0.56 percent rising and 0.36 percent falling, which on a 3.3 V bias is 18.5 mV and 11.9 mV, so the pin can be driven from a low voltage logic rail with a pull-up below 35 kOhm. That ratioed threshold is worth knowing, because it means the enable does not need a level translator on a 1.2 V logic board.

Order code and stock

EUFD is the extended grade QFN on tape and reel, IUFD the industrial grade, MPUFD the -55 C to 125 C version, and the PBF suffix is the tray. The exposed pad is ground on this part, which is the opposite of the negative regulators in this catalogue and the reason the two should never be confused on a bill of materials. The power management cross reference separates the positive and negative families, the lead time page carries the QFN schedule, and BOM shortage recovery covers the grade options.