Contact Us

LT3065MPDD#TRPBF

Brand: Analog Devices
Analog Devices LT3065MPDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3065MPDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3065MPDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3065MPDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3065MPDD#TRPBF: the same minus 55 C regulator in a 3 mm DFN

The LT3065MPDD#TRPBF is the MP grade of the LT3065 in the 10-lead 3 mm by 3 mm DFN, taped and reeled. Electrically it is the same part as the MSOP code: 1.6 V to 45 V input, 500 mA output, 0.6 V to 40 V adjustable, a resistor on IMAX for current limit, PWRGD for status, and a capacitor on REF/BYP for noise and soft start. What changes is the body. The DFN is 2 mm shorter than the 12-lead MSOP and carries its ground through an exposed pad that is also pin 11, so the thermal path is the board copper rather than the package body.

Published values

ParameterValue
Input voltage1.6 V to 45 V, 2.2 V maximum at 500 mA
Output voltage0.6 V to 40 V adjustable
Output current500 mA, internal limit 520 mA minimum
Dropout voltage300 mV typical at 500 mA, 350 mV maximum
GND pin current55 uA no load, 11 mA at 500 mA
Output noise25 uV RMS with 10 nF on REF/BYP
Ripple rejection70 dB minimum at 120 Hz
Thermal resistance31 C/W junction to ambient, 9 C/W to case
Exposed padPin 11, ground, must be soldered to the board
Grade and package10-lead 3 mm DFN, minus 55 C to 150 C, tape and reel

The DFN is not the better thermal choice here

It is worth reading the two package tables side by side before choosing on size. The 10-lead DFN quotes 31 C/W junction to ambient and 9 C/W junction to case. The 12-lead MSOP quotes 28 C/W and 6 C/W. The smaller body is worse on both, because the MSOP has a longer lead frame and a larger exposed pad behind the die. At 1.5 W of dissipation, which is a 5 V to 3.3 V drop at 500 mA plus quiescent, the difference is about 4.5 C of junction rise, small but not zero in a sealed box. The DFN earns its place on height and on board area, not on thermal margin, and a file that moves from MSOP to DFN to save space should recheck the ambient budget rather than assume the change is neutral.

Why the pad is ground, not output

Positive regulators from this family bring the pad out as ground, which is the opposite of the negative regulators in the same catalogue where the pad is the output node. On a DFN that matters for three reasons: the pad is the only heat path, so it needs a via array into a copper pour; it is also the return for the reference and the error amplifier, so a noisy ground under the pad shows up as output noise; and a small thermal relief pattern that is good practice on a hand soldered part is the wrong choice here, since it adds thermal resistance exactly where the part is trying to shed heat. A solid connection to a ground plane with nine or more vias is the usual arrangement, and it has to be present on both sides of the board.

Temperature window and derating

The MP grade is tested from minus 55 C to 150 C at the junction, which is a wider window than the H grade on the same die: the H part is tested at 150 C but specified from minus 40 C. The difference is the cold end, and it is the cold end that catches industrial programs with outdoor cabinets. The vendor also states that lifetime is derated above 125 C, so the 25 C between 125 and 150 is overload headroom rather than an operating point. For a 60 C ambient box with 1.5 W in the part, the junction sits near 107 C and the part runs inside the derating line, which is the honest place to be.

Order code and replacement

The MPDD code is tape and reel; the same die is available in the MSOP as MPMSE and in the E, I and H grades of both bodies. A substitution across grades keeps the pinout and the electrical table but changes the test coverage, and a substitution across bodies changes the footprint, so the two cases have to be handled differently in a shortage. Files that mix these codes are best held on one cross reference, which is what the power management cross reference is for. Short line items are handled on the BOM shortage recovery page, and the cost side of grade substitution is covered on the component cost page.