LT3065IMSE#TRPBF
Product Specifications
LT3065IMSE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3065IMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3065IMSE#TRPBF: the industrial grade 500 mA regulator with a real minus 40 C guarantee
The LT3065IMSE#TRPBF is the I grade of the LT3065 in the 12-lead MSOP, taped and reeled. The electrical table is the family table: 1.6 V to 45 V input, 500 mA, 300 mV of dropout at full load, 25 uV RMS of noise with a 10 nF bypass, a programmable current limit accurate to plus or minus 10 percent, and a PWRGD flag. What the I code buys over the E code is coverage. The I grade is guaranteed over the full minus 40 C to 125 C junction range, while the E grade is tested at 25 C and only guaranteed from 0 C to 125 C, with the cold end assured by characterization.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 1.6 V to 45 V, 2.2 V maximum at 500 mA |
| Output voltage | 0.6 V to 40 V adjustable |
| Output current | 500 mA, 520 mA minimum internal limit |
| Dropout voltage | 110 mV at 10 mA, 220 mV at 100 mA, 300 mV at 500 mA typical |
| GND pin current | 55 uA no load, 270 uA at 10 mA, 11 mA at 500 mA |
| Output noise | 90 uV RMS bare, 25 uV RMS with 10 nF on REF/BYP |
| Ripple rejection | 70 dB minimum, 85 dB typical at 120 Hz |
| PWRGD leakage | 0.01 uA at 45 V, 0.07 V low at 50 uA |
| Shutdown current | 0.2 uA typical, 1 uA maximum at 45 V |
| Thermal resistance | 28 C/W junction to ambient, 6 C/W to case |
| Grade and package | 12-lead MSOP, minus 40 C to 125 C, tape and reel |
Where the grade shows up in a real file
On paper the E and I codes look interchangeable, and on a bench at 22 C they are. The difference appears in three places. First, a product that is stored or shipped through minus 30 C and then powered up: the I grade carries a specification there, the E grade carries a characterization note. Second, a program with a documented incoming inspection that reads the order code against the drawing: an E grade on a drawing that calls for I is a finding regardless of behaviour. Third, warranty terms, where the same finding becomes a cost argument after a field return. The I grade is the default choice for industrial controllers, telecom line cards and anything that leaves a heated room, and the price difference against the E grade is usually small enough that the paperwork is the bigger factor.
PWRGD as a sequencing signal
The flag trips at 90 percent of nominal on the way up, with a 86 to 94 percent window over temperature and 1.6 percent of hysteresis. That window is wide enough that a supervisor downstream cannot rely on it as a precision threshold, and it is meant to be used as a sequence signal rather than a measurement. The useful behaviour is at power down: because the flag follows the output rather than the input, a downstream converter can be held off before the rail collapses, which is the difference between a clean brownout and a reset loop. The pin is open drain, leaks 0.01 uA at 45 V and pulls down to 0.07 V at 50 uA, so a 100 kOhm pull up to 3.3 V is enough and the pin is safe on a 45 V rail.
Divider, bypass and current limit in one place
Three components set the behaviour of this part and they interact. The divider on ADJ sets the output, with R1 no larger than 62 kOhm so the divider current stays at 10 uA and the 16 nA of ADJ bias current stays a small fraction of it. The capacitor on REF/BYP sets the noise and the soft start: 10 nF takes the noise to 25 uV RMS at 0.6 V, and a larger value slows the ramp, which is how an inrush sensitive rail is protected. The resistor on IMAX sets the limit, 1.5 kOhm for about 200 mA, 604 Ohm for about 495 mA, and the tolerance is plus or minus 10 percent over input voltage and temperature. The output capacitor must be at least 3.3 uF of ceramic, which is the minimum for stability, not a recommendation.
Buying the industrial grade
The I grade sits between the E and the H codes in price and is the one that distributors hold in the deepest quantity, though depth varies by month and by body. Files that need a consistent grade across several rails are best kept on one cross reference, which is what the power management cross reference covers. Mixed BOMs are consolidated on the one stop BOM sourcing page, and schedule changes on the MSOP body are tracked on the lead time page.