Contact Us

LT3065EDD#TRPBF

Brand: Analog Devices
Analog Devices LT3065EDD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3065EDD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3065EDD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3065EDD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3065EDD#TRPBF: standard grade 500 mA regulator in the 10-lead DFN

The LT3065EDD#TRPBF is the E grade of the LT3065 in the 10-lead 3 mm by 3 mm DFN, taped and reeled. It is the smallest and cheapest way to buy this regulator family: 1.6 V to 45 V input, 500 mA output, a 0.6 V to 40 V adjustable output, 300 mV of dropout at full load, a resistor programmable current limit and a PWRGD flag. The E suffix means tested at 25 C with 0 C to 125 C guaranteed; the DFN suffix means a 3 mm body with the ground on an exposed pad that is also pin 11.

Published values

ParameterValue
Input voltage1.6 V to 45 V, 2.2 V maximum at 500 mA
Output voltage0.6 V to 40 V adjustable
Output current500 mA, 520 mA minimum internal limit
Dropout voltage300 mV typical at 500 mA, 350 mV maximum
GND pin current270 uA at 10 mA, 11 mA at 500 mA
Output noise25 uV RMS with 10 nF on REF/BYP
ADJ bias current16 nA typical, 60 nA maximum
PWRGD trip point90 percent nominal, 1.6 percent hysteresis
Thermal resistance31 C/W junction to ambient, 9 C/W to case
Exposed padPin 11, ground, must be soldered
Grade and package10-lead 3 mm DFN, 0 C to 125 C guaranteed

The heat path is the board, not the package

With 31 C/W junction to ambient and 9 C/W junction to case, this part dumps most of its heat into the pad and from there into the copper. The number that matters is not the package figure but the copper area under and around it: the vendor's rating assumes a defined test board, and a real board with two layers and a small pour will run hotter. At 1.4 W, which is a 5 V to 3.3 V drop at 500 mA plus quiescent, the rise is about 43 C and a 70 C ambient lands the junction near 113 C. That is inside the window but with little left for a hot day, which is why the usual arrangement is a ground pour on both sides stitched with vias under the pad rather than a single layer connection.

What the DFN costs in assembly

The package is 3 mm square with a 0.5 mm pitch, comfortably inside standard assembly, but the exposed pad brings three requirements. The stencil needs an aperture that leaves roughly half the pad area covered in paste. The vias under the pad must be tented or plugged so paste is not wicked away during reflow. And the part must be inspected by X-ray, because a partly voided pad passes a functional test at low load and fails a thermal test at full load. None of that is unusual in 2026, and all of it depends on the assembly house being told what the pad is for rather than being handed a footprint from a library.

Noise and the two capacitors that set it

The bare regulator is a 90 uV RMS part from 10 Hz to 100 kHz. The first capacitor, 10 nF from REF/BYP to ground, takes that to 25 uV RMS at a 0.6 V output and doubles as the soft start ramp. The second, a feedforward capacitor from OUT to ADJ, is what keeps the noise from rising with the output voltage, because above 0.6 V the divider amplifies the reference noise. The vendor's rule is that doubling the divider current means doubling the feedforward capacitor, which matters if a file changes the divider to save standing current. The output capacitor is 3.3 uF ceramic minimum for stability, and a capacitor with a strong DC bias coefficient can lose half its value at the operating voltage, so the effective value is what counts.

When the standard grade fits

This code suits indoor equipment, bench instruments and any board with no cold start requirement, and it is the natural choice where a system already has a 45 V bus and needs a quiet 3.3 V or 5 V rail at half an amp. Where the same board is sold into an outdoor cabinet, the I grade on the same DFN is the substitution and the footprint does not change. Keeping both codes visible on one cross reference is what the power management cross reference is for; the shortage route is on the BOM shortage recovery page, and the cost of a grade change is worked through on the component cost page.