LT3060MPTS8-3.3#TRPBF
Product Specifications
LT3060MPTS8-3.3#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3060MPTS8-3.3#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3060MPTS8-3.3#TRPBF: the 3.3 V fixed option in the minus 55 C ThinSOT
The LT3060MPTS8-3.3#TRPBF is the 3.3 V fixed version of the LT3060 in the 8-lead ThinSOT, tape and reel, MP grade. It runs from 1.6 V to 45 V, sources 100 mA, and holds 3.3 V to 3.234 V at the low end and 3.366 V at the high end over line, load and the whole temperature window. The intended job is a quiet 3.3 V rail on a board that already has a 12 V or 24 V bus and cannot afford a switcher for a few tens of milliamps. Quiescent current is 40 uA, so the part can stay alive on a battery branch while the rest of the board is off.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 1.6 V to 45 V, 50 V absolute maximum |
| Output voltage | 3.3 V fixed, 3.234 V to 3.366 V over temperature |
| Line regulation | 1.3 mV typical, 7 mV maximum, E and I grades |
| Load regulation | 3.1 mV typical, 24 mV maximum, 1 mA to 100 mA, E and I grades |
| Dropout voltage | 300 mV typical at 100 mA |
| Quiescent current | 40 uA typical at no load |
| Output noise | 30 uV RMS with 10 nF on REF/BYP |
| Reverse output current | Tested with input grounded, output forced to rated voltage |
| Package | 8-lead ThinSOT, part marking LTFWG |
| Thermal resistance | 57 C/W to 67 C/W junction to ambient, 25 C/W to case |
| Grade | MP, minus 55 C to 150 C junction |
Where the 3.3 V tolerance comes from
The regulated output window on this code is wider than the 25 C figure suggests. At 25 C, with a 3.85 V input and a 1 mA load, the part sits between 3.267 V and 3.333 V. Over the full 3.85 V to 45 V input range and 1 mA to 100 mA load, the E and I grades are specified to 3.234 V and 3.366 V, and the MP and H grades open to 3.218 V on the low side because the wider temperature window costs some reference accuracy. A 3.3 V logic rail has plenty of room inside that. A 3.3 V rail feeding a precision reference or an ADC input does not, and in that case the money is better spent on a reference than on a tighter regulator grade.
Reading the MP and H distinction
Both wide temperature codes are tested at 150 C, but they are not the same part on paper. The MP grade is tested from minus 55 C to 150 C. The H grade is tested at 150 C and guaranteed from minus 40 C. The 15 C difference at the cold end is the whole reason both codes exist: an avionic or outdoor telecom line that has to start at minus 45 C needs the MP code, and an industrial line that stops at minus 40 C can use the H code and usually pays less. Buyers who substitute one for the other in either direction are changing a qualification claim, and that change should be documented rather than discovered in a temperature chamber.
Dissipation from a 12 V or 24 V rail
From 12 V to 3.3 V at 100 mA the part dissipates 0.87 W. At 57 C/W that is a 50 C rise, which is comfortable from a 70 C ambient and tight from 85 C. From 24 V the figure becomes 2.07 W and 118 C of rise at 57 C/W, which fails an 85 C ambient without help. The vendor's published worked example uses a 12.6 V input, a 2.5 V output and 50 mA, which is 0.513 W and a 27.8 C rise at 54 C/W, ending at 112.8 C from an 85 C ambient. The same arithmetic on this 3.3 V code with a 24 V input says the honest load is nearer 30 mA in the ThinSOT body unless the copper under the part is generous and the ambient is lower than an enclosure would suggest.
What to check before substituting
The family has fixed options at 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V and 15 V, plus an adjustable version with a 600 mV reference. Dropping to a different fixed voltage changes the die, so the part marking changes with it and a substitution is visible on the reel label. Moving between the ThinSOT and the 2 mm DFN changes the footprint and the exposed pad connection, since the DFN pad is ground and has to be soldered. Both cases are covered on the pin to pin cross reference, the grade trade-off is priced out on the component cost page, and consolidated buying across the rails is on one stop BOM sourcing.