LT1763IS8-5#TRPBF
Product Specifications
LT1763IS8-5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1763IS8-5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT1763IS8-5#TRPBF: the 5 V fixed low noise regulator in the 8 lead SO body
What this order code is
LT1763IS8-5#TRPBF is the 5 V fixed member of the LT1763 family in the 8 lead SO body, industrial grade, lead free, on tape and reel. It delivers 500 mA with 300 mV of dropout, draws 30 microamps with the quiescent current controlled in dropout, and reaches 20 microvolts RMS of output noise with a 0.01 microfarad bypass capacitor. The fixed output removes the feedback divider entirely, and the internal protection covers reverse battery, reverse current, current limit and thermal limit without an external diode.
A 5 V output from this family is a post regulator. From a 6 V input at full load the dissipation is 0.5 W, which the SO body can pass with reasonable copper, and from 7 V it is 1 W, which is at the edge. From 12 V it is 3.5 W, which is not a package question at all. The value of the part on a 5 V rail is the noise and the dropout, not the efficiency, and that is why it usually sits behind a switching converter rather than directly on a 12 V bus.
Parameters as published
| Item | Value |
|---|---|
| Output voltage | 5 V fixed |
| Output current | 500 mA |
| Dropout at 500 mA | 300 mV |
| Minimum usable input at full load | 5.3 V |
| Input range | 1.8 V to 20 V |
| Quiescent current | 30 microamps, controlled in dropout |
| Shutdown current | under 1 microamp |
| Output noise | 20 microvolts RMS with a 0.01 microfarad bypass capacitor |
| Minimum output capacitor | 3.3 microfarads |
| Protection | reverse battery, reverse current, current and thermal limit |
| Body | 8 lead SO, no exposed pad |
| Temperature grade | industrial |
| Packing | tape and reel, lead free |
Numbers that decide the application
The dissipation line is the same at every current: 1 V of drop per amp at a 6 V input, so 0.5 W at 500 mA, 0.3 W at 300 mA and 0.1 W at 100 mA. On a 7 V input the numbers double, and 1 W in an 8 lead SO with no exposed pad is where the junction temperature starts to be the limiting specification rather than the current rating. A 5 V rail that has to deliver 500 mA on a 12 V bus is a two stage job, and the linear stage is there to remove the switching residue rather than to drop the voltage.
The minimum input is 5.3 V at full load, so an intermediate bus at 5.5 V leaves 200 mV for the converter tolerance and the load step. That is thin. A 6 V intermediate bus leaves 700 mV, which covers a plus or minus 5 percent upstream rail and a fast load step, and it also keeps the pass device out of dropout during a transient, which is where the quiescent current control earns its place. A part that lets its quiescent current climb in dropout turns a short transient into a much larger input current spike than the upstream converter was sized for.
Twenty microvolts RMS on a 5 V full scale is 0.26 of a 16 bit least significant bit, so this regulator is not the limit of a 16 bit channel and it becomes relevant at 18 bits and above. The figure requires the 0.01 microfarad bypass capacitor, and it also assumes a quiet input: a linear regulator rejects switching residue at a rate that falls with frequency, so most of the work is done by the input capacitor and the converter that feeds it. A 3.3 microfarad minimum output capacitor is a stability requirement, and a ceramic part is acceptable without a series resistor.
Where it fits and where it does not
It fits a 6 V or 5.5 V intermediate bus, a cleaned 5 V analogue rail behind a buck, and boards with an existing SO 8 footprint that need 5 V at a few hundred milliamps. It does not fit a 12 V input at high current, a 5 V input, or a board that needs the full 500 mA from a 7 V rail in a warm enclosure. It also does not fit a rail that has to come up before its input is stable, because the part follows the input down rather than holding the output off.
Supply and second source questions
The questions we get on this code are about the input rail, the body and the temperature grade. The 5 V fixed output appears in the family in both the SO and the DFN bodies and in three temperature grades, and while the electrical table is shared, the thermal path is not. A substitution that keeps the voltage and the current but changes the body is the one that shows up as a hot part rather than as a failed part. The members that share the die and the ones that only look similar are listed on the power management cross reference page.
Sourcing notes and next step
We quote this code against the bill of materials and check the four fields that decide whether the line runs: output voltage, body, grade and reel. Where the exact code is short we will say so rather than substitute the DFN member without telling the buyer that the footprint changes. Send the line items, quantities and required date through the BOM shortage recovery page, and where a board is being kept in production past the end of a catalog life, the obsolete part cross reference hub is where the parts still in production but no longer recommended for new builds are tracked. The family list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty