HMC994APM5E
Product Specifications
HMC994APM5E
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC994APM5E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC994APM5E: DC to 28 GHz in a 5 mm package
The HMC994APM5E is the surface mount order code of the DC to 28 GHz distributed power amplifier, in a 32 lead 5 mm by 5 mm body on 25 square millimetres of board, drawing 250 mA from 10 V. Gain is 15 dB, saturated output 29.5 dBm, output third order intercept 38 dBm at 16 dBm per tone and the output return loss is 22 dB in the middle band. The package is a lead frame part rather than a ceramic, so what it changes against the die order code is the port transition above 20 GHz, the thermal path under 2.5 W of DC and the assembly process.
Published values
| Parameter | Value |
|---|---|
| Package | 32 lead, 5 mm by 5 mm, 25 square millimetres |
| Frequency range | DC to 28 GHz |
| Gain | 14 dB, 15 dB and 16 dB typical across DC to 10, 10 to 20 and 20 to 28 GHz |
| Gain flatness | plus or minus 0.5 dB inside each band |
| Output power at 1 dB compression | 28 dBm, 28 dBm and 27 dBm |
| Saturated output power | 30 dBm, 29.5 dBm and 28 dBm |
| Output third order intercept | 40 dBm, 38 dBm and 36 dBm at 16 dBm per tone |
| Output return loss | 25 dB, 22 dB and 20 dB |
| Input return loss | 12 dB across the band |
| Noise figure | 3.5 dB to 4.0 dB |
| Supply | 10 V at 250 mA, 2.5 W of DC |
| Gate bias | VGG2 at 3.5 V typical, VGG1 adjusted for 250 mA |
Two and a half watts inside a plastic body
The DC input is 2.5 W and the output at the low band saturated point is 1 W, so 1.5 W of heat leaves through a lead frame and an exposed paddle. That is five times the dissipation of a small signal part in the same footprint, and it means the paddle is not a convenience but the only path. A via field under the paddle, soldered with no voids, and a ground plane on the far side are the minimum, and the plane has to extend beyond the package outline or the spreading resistance becomes the limit.
The plastic body also sets a moisture sensitivity level, which the ceramic code in the same family does not. That matters for a build that stores parts in a dry cabinet and then reflows them weeks later: the bake requirement, the floor life after opening and the reflow profile all come from the package rather than from the amplifier, and the profile has to be the one for this body even though the die is identical to the ceramic code.
Where the package is felt at 28 GHz
At 28 GHz the free space wavelength is 10.7 mm and the wavelength on a board is closer to 6 mm, so a lead frame of a couple of millimetres is a third of a wavelength. The package transition therefore cannot be treated as a lumped element, and the input return loss of 12 dB across the band is the figure that shows it: a die assembly can beat that, a package generally cannot.
The output side is less sensitive because the output impedance of a power stage is low and the return loss is 20 dB or better, but the same transition reduces the voltage swing available before compression, which is why the top band compression point is 27 dBm against 28 dBm in the low band. For a 28 GHz application the arithmetic is simple: budget the gain and the compression point on the top band, not on the headline row.
Sequencing and the second gate at 3.5 V
VGG2 at 3.5 V is a bias gate referenced to the drain, not a control input. It has to be present before the drain current is set, and it has to stay present until the drain is removed. A single toggle that removes all rails together is acceptable if the negative gate falls first, and it is not acceptable if the drain falls first.
A practical sequence for a production fixture is a negative gate rail always on, then the drain, then VGG2, then VGG1 walked up to 250 mA. Shutdown reverses it. The measurement that proves the sequence is the drain current during power up, which should stay under a few milliamps until the last step, and it is worth adding to the test program because a wrong sequence does not fail immediately, it shortens the life of the output device.
When an order code in this family cannot be found, the RF power transistor cross reference lists what else does the same job, RF procurement covers what to check before a part is dropped into an existing board, and one stop BOM sourcing is the route we take on a live shortage.
Two questions buyers ask
Can the package be used to 28 GHz in a 50 ohm system? Yes, with 12 dB of input return loss and 20 dB of output return loss at the top band, and with the compression point budgeted at 27 dBm rather than 28 dBm.
Does the 25 percent efficiency headline describe the heat? No. The DC input is fixed at 2.5 W, so the heat is 2.5 W minus the output, and the worst case is at low drive.