Contact Us

HMC659LC5

Brand: Analog Devices
Analog Devices HMC659LC5 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC659LC5 — Analog & Mixed-Signal ICs | Superb Automation

HMC659LC5

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC659LC5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC659LC5: a ceramic 5 by 5 body for the DC to 15 GHz power amplifier

The HMC659LC5 is the ceramic surface mount order code of the DC to 15 GHz pHEMT power amplifier: a leadless 5 mm by 5 mm body, 25 square millimetres of board, 19 dB of gain, 28.5 dBm saturated, 300 mA from 8 V and an output third order intercept of 35 dBm in the low band. The ceramic body is the reason this code exists in defence and instrumentation work, because it tolerates a wider assembly process window than a moulded plastic package and because its thermal path goes through a ceramic floor rather than through a lead frame and a mould compound.

Published values

ParameterValue
Bodyleadless 5 mm by 5 mm ceramic, 25 square millimetres
Frequency rangeDC to 15 GHz, three bands
Gain19 dB, 18 dB and 17 dB typical across the bands
Output power at 1 dB compression26.5 dBm, 27.5 dBm and 26.5 dBm
Saturated output power28.5 dBm in the middle band, 27.5 dBm at the top
Output third order intercept35 dBm, 32 dBm and 29 dBm
Noise figure2.5 dB typical 6 to 11 GHz, 3.0 dB below, 3.5 dB above
Return loss20 dB in and 19 dB out in the low band
Supply8 V at 300 mA, 2.4 W of DC
Gate biasVGG1 adjusted for 300 mA, VGG2 at 3 V
Dissipation at the saturated point1.69 W
Assemblyreflow or epoxy attach, no wire bonding on site

Why a ceramic body and not a plastic one in the same socket

The amplifier is identical between the plastic and ceramic codes, so the electrical reason to choose ceramic is small and the mechanical reason is the whole story. A ceramic floor conducts heat better than a lead frame under a mould compound, and it expands with a coefficient closer to the alumina and the kovar around it, so a module that goes through a temperature cycle from minus 55 to plus 125 degrees has less strain at the solder joints of this part than it would with a plastic body.

The other half is moisture and outgassing. A ceramic body has no absorbed moisture to release during reflow, so it does not need the bake cycle that a plastic part at moisture sensitivity level three or four requires, and it does not contribute volatiles inside a sealed module where they would condense on a cold surface. For a hermetic assembly that second point is often the deciding one.

Heat through a ceramic floor at 1.69 W

At 28.5 dBm the part delivers 708 mW and dissipates 1.69 W. Through a ceramic floor of 25 square millimetres that is a manageable flux, and the limiting resistance is again the solder joint and the board rather than the body. What a ceramic body changes is the number of interfaces: ceramic, metallisation, solder, board, where a plastic part has mould compound, lead frame, solder, board. Fewer interfaces means a more predictable rise and a smaller spread between units.

The practical number to work to is the one the derating curve implies. With a channel limit near 150 degrees and 1.69 W of dissipation, the allowed package to channel resistance has to stay in the twenties of degrees per watt, which is met by a well soldered ceramic floor on a copper plane and is not met by a part standing on four corner pads with no thermal pad connection.

What to measure on a first article from a new lot

Gain at 1 GHz, 8 GHz and 14 GHz covers the three bands, and the compression point at 8 GHz is the one that catches a degraded output stage, because it is the band where the part is specified hardest. Return loss at 8 GHz of 18 dB input and 20 dB output is a good joint check.

The gate voltage needed for 300 mA is the drift indicator. This family spreads several hundred millivolts in threshold, so the absolute number is not a limit, but a lot that needs a gate voltage 300 mV away from the previous lot is worth a conversation with the supplier before it goes into a build, because the difference usually comes from a process change rather than from wafer position.

Where a customer needs a second position on this part, defense grade components is the starting point, RF procurement sets out the checks a substitution has to pass, and obsolete RF part replacement is the short lead time route we quote against.

Two questions buyers ask

Is the LC5 electrically identical to the die? The amplifier is the same. The published table comes from the packaged part, so the die is expected to be at least as good at the top of the band, and the difference has to be measured rather than assumed.

Does ceramic mean hermetic? No. A leadless ceramic body is not a hermetic cavity part, so screening and leak testing have to be asked for explicitly if the programme needs them.