Contact Us

ATMEGA649V-8AU

Brand: Analog Devices
Analog Devices ATMEGA649V-8AU is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ATMEGA649V-8AU — Analog & Mixed-Signal ICs | Superb Automation

ATMEGA649V-8AU

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ATMEGA649V-8AU from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ATMEGA649V-8AU: 64 kB of flash with an LCD driver, running to 8 MHz from 1.8 V

The ATMEGA649V-8AU is an 8-bit AVR microcontroller with 64 kB of in system programmable flash, 2 kB of EEPROM, 4 kB of SRAM and a four by 25 segment LCD driver on the same die. The V suffix is the low voltage speed grade: 8 MHz from 1.8 V to 5.5 V, where the non V part needs 4.5 V to reach 16 MHz. For a battery instrument with a segment display, that combination is the reason the part is still specified into new boards.

Published values

ParameterValue
Core8-bit AVR RISC, up to 16 MIPS at 16 MHz
Speed grade, V part8 MHz from 1.8 V to 5.5 V
Flash64 kB, in system programmable, read while write
EEPROM2 kB, 100,000 write cycles
SRAM4 kB
LCD driver4 x 25 segments, internal contrast control
ADC8-channel, 10-bit
TimersTwo 8-bit, one 16-bit, real time counter, four PWM channels
SerialUSART, SPI, USI with start condition detector
GPIO54 lines
Active current350 uA at 1 MHz and 1.8 V
Power down current100 nA at 1.8 V
Package64-lead TQFP, 14 mm x 14 mm x 1.0 mm
Temperature-40 C to +85 C industrial

The V suffix changes the whole power budget

Running to 8 MHz at 1.8 V is what allows the part to sit directly on two alkaline cells without a boost converter. A non V part at the same voltage is limited to a lower clock, and a board that substitutes one for the other will either fail to start at the low end of the battery curve or run the timing loops at the wrong rate. The suffix is part of the electrical specification, not a packing code.

The current figures set the rest of the budget. 350 uA at 1 MHz and 1.8 V, and 100 nA in power down, mean the display and the sensor usually dominate the average current, so the firmware decision that matters is how long the core stays awake per measurement, not which sleep mode is used.

What an integrated LCD driver saves

A four by 25 segment driver inside the microcontroller removes an external driver IC, its own supply decoupling and the serial link to it. On a metering or a thermostat board that is a smaller bill of materials and one less part to qualify for a long life product. The internal contrast control also removes the trim potentiometer that an external driver would need over temperature.

Programming and debug

The part supports in system programming through SPI, a boot loader in the boot section, and JTAG for boundary scan and on chip debug. A production line can programme it after placement, which matters on a board where the microcontroller is soldered on both a main board and a display board revision.

Buyers usually arrive at one stop BOM sourcing to find the family alternatives, then use OEM procurement to confirm a substitute before it is fitted; BOM shortage recovery is the routine for a part that has already stopped shipping.

Two questions buyers ask

Can the ATmega649 replace the ATmega649V in a 3.3 V board? Yes, the non V part runs to 16 MHz at 4.5 V and works at 3.3 V on a lower clock. The firmware timing has to be checked because the maximum clock at 3.3 V differs between the two grades.

Is the 64-lead QFN version the same die? It is the same family and memory map in a different package, with 64 pads instead of 64 leads. The pin numbering differs, so it is not a drop in.