ADR381ARTZ-REEL7
Product Specifications
ADR381ARTZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADR381ARTZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADR381ARTZ-REEL7: A 2.500 V Reference in Three Pins That Works Down to 2.8 V In
The ADR381 is a 2.500 V band gap reference in a 3-lead SOT-23, and its sibling the ADR380 is the same part at 2.048 V. Initial accuracy is plus or minus 6 mV maximum, which is 0.24 percent, the temperature coefficient is 25 ppm per degree C maximum, load regulation is 70 ppm per mA and line regulation is 25 ppm per V. It operates from 2.8 V to 18 V, draws 120 uA maximum, sources or sinks up to 5 mA and is specified from minus 40 C to plus 85 C. The reel suffix identifies the packaging, not a grade, so the electrical limits are the same as for any other ADR381 in the same temperature band.
Why 2.048 V and 2.500 V are two different products
2.048 V is a binary value: it divides by two eleven times without a remainder, so a 12-bit converter with a 2.048 V reference has a code size of exactly 500 uV and a 16-bit converter has one of 31.25 uV. That makes every subsequent calculation in firmware a shift rather than a multiply, and it is why instrumentation converters often specify a 2.048 V reference. 2.500 V is a decimal value and its code sizes are 610 uV at 12 bits and 38.1 uV at 16 bits, which are round in engineering units and awkward in binary. The choice between the two parts is therefore about the arithmetic in the host as much as about the analogue circuit.
Drift over temperature is larger than the initial error
The 25 ppm per degree C maximum coefficient, applied over the 125 degrees from minus 40 C to plus 85 C, accumulates to 3125 ppm, which is 7.8 mV on 2.5 V or 0.31 percent. The initial accuracy of 0.24 percent is therefore the smaller of the two errors once the part is used over its full range, and a specification that quotes only the initial figure describes a 25 C measurement rather than a product. For a 12-bit converter on a 2.5 V span, 7.8 mV is 12.8 codes, so an uncalibrated absolute measurement drifts by about 13 codes across temperature even with a perfect converter behind it.
| Parameter | Value | What it decides |
|---|---|---|
| Output | 2.500 V | 610 uV per code at 12 bits, 38.1 uV at 16 bits |
| Initial accuracy | Plus or minus 6 mV maximum, 0.24 percent | A 25 C number, not an over temperature one |
| Temperature coefficient | 25 ppm per degree C maximum | 7.8 mV over the full 125 degree range |
| Load regulation | 70 ppm per mA | 875 uV at the full 5 mA load |
| Line regulation | 25 ppm per V | Matters when the input rail is not well regulated |
| Supply range | 2.8 V to 18 V | 300 mV of dropout above the output |
| Supply current | 120 uA maximum | 600 uW at 5 V for the reference alone |
| Output current | 5 mA | Can bias a small bridge directly |
| Temperature | Minus 40 C to plus 85 C | Industrial, not extended industrial |
| Package | 3-lead SOT-23 | One pin in, one pin out, one ground |
Three pins is a feature, and a limitation
A three pin reference has no noise reduction pin, no trim pin and no shutdown pin, so nothing can be adjusted after assembly and the part cannot be turned off to save current. What it does have is a supply range down to 300 mV above its output, which means a 2.500 V reference can run from a 3.0 V rail that is at the bottom of its tolerance, and it can source enough current to bias a small bridge without a buffer. Where a product needs lower noise, a trim, or a shutdown, a larger package with those pins is the answer, and the cost is board area and often supply current.
Where the part fits
Battery powered instrumentation, portable medical instruments, data acquisition systems, industrial process control, disk drives and automotive electronics are the named applications, with the automotive use resting on the wide supply range and the small body rather than on an extended temperature grade. The reference is usually the accuracy limit in a measurement chain, so it belongs in the error budget with its drift term included, not just its initial tolerance. For converter pairings, the ADC and DAC cross reference page lists references that match common converter codes, the medical device components page covers the instrument qualification side, and the component lead time solutions page covers supply on small outline references.
Line regulation and the rail the reference sits on
Line regulation of 25 ppm per V means the output moves by 2.5 ppm for every 100 mV of input change, which is 6.25 uV on a 2.5 V output. That sounds negligible until the input is a switching converter with 50 mV of ripple at 500 kHz, where the reference sees the ripple across its own regulation bandwidth and passes a fraction of it to the converter. The minimum input of 2.8 V leaves 300 mV above the output, so a 3.0 V rail at minus five percent, which is 2.85 V, still has 50 mV of headroom and stays in regulation, while a 3.0 V rail at minus ten percent does not. That margin is the reason the part works on a 3 V system and fails on a 2.5 V one.