Contact Us

ADPA9002ACGZN

Brand: Analog Devices
Analog Devices ADPA9002ACGZN is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADPA9002ACGZN — Analog & Mixed-Signal ICs | Superb Automation

ADPA9002ACGZN

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADPA9002ACGZN from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADPA9002: 29 dBm and 43 dBm of intercept from a 12 V rail with no negative supply

The ADPA9002 is a gallium arsenide amplifier for dc to 5 GHz with 29 dBm of output power at one decibel compression, up to 15 dB of gain and an output third order intercept up to 43 dBm, self biased at 12 V and 385 mA in a 32-lead, 5 mm by 5 mm LFCSP. The self bias is the feature that gets it built into instrument and cable products: there is no negative gate supply to sequence, and the optional VGG1 pin is only there for trimming the quiescent current, with ground giving the nominal point.

Published values

ParameterValue
Frequency rangedc to 5 GHz, specified as two slices
Output power at one decibel compression29 dBm typical
Gainup to 15 dB typical
Output third order interceptup to 43 dBm typical
Supply12 V self biased at 385 mA typical
Quiescent current trimVGG1 pin, ground for nominal, positive for adjustment
Package32-lead, 5 mm by 5 mm LFCSP
Matching50 ohm input and output
Intercept headroom14 dB above the compression point
Typical usetest instrumentation, cable systems, general purpose drivers

Self bias removes the sequencing problem

A depletion mode stage needs a negative gate before the drain, and every circuit that uses one needs a sequencer or a bias controller to make that happen in the right order. The ADPA9002 does that internally and presents a part that runs from a single 12 V rail at 385 mA, with the gate voltage generated on chip. For a multi channel instrument this is one supply and no sequencing state machine per channel.

It also removes a failure mode. A bias controller that comes up in the wrong order, or that loses its negative rail during a brownout, turns the amplifier into a short across the 12 V supply. The self biased part has no such window, which is why it turns up in equipment that is powered on and off by users rather than by a controlled sequence.

Twelve volts and 385 mA is 4.6 W, most of it heat

The DC input is 4.62 W against 0.79 W of output at the one decibel compression point, so 3.36 W is dissipated at full drive and slightly less at lower drive. A 5 mm package handles that with a proper pad, and the board needs a thermal path under it, but the number to notice is that the part draws 4.6 W whether or not there is a signal, which sets the idle temperature of the enclosure.

Because the bias is internal, the drain current moves with temperature on its own. The data sheet quiescent figure is at 25 degrees, and a board inside a closed chassis at 70 degrees will draw more. A power budget written from the 25 degree number underestimates the supply and the heat in exactly the enclosure that has no fan.

Forty-three dBm of intercept against 29 dBm of compression

Fourteen decibels between the third order intercept and the one decibel compression point is a linear part by the standards of this family, where the power stages sit at 10 dB or less. That is what makes it usable as the stage before an analyser front end or in a cable return path where several carriers share the same amplifier.

The trade is efficiency: a linear stage runs at a lower percentage of its DC input turned into output, and this one converts about 17 percent at the compression point. For a driver that is acceptable, and for a transmitter final stage it is not. The part is a driver and a buffer, not a power stage.

For a board that has to keep running while a reel runs out, the amplifier cross reference is where the family alternatives sit, the RF component sourcing page is the check list before a substitute goes in, and how to verify a drop in replacement is how a gap is covered without a new line item.

Two questions buyers ask

Does the part need a negative supply? No. It is self biased from a single 12 V rail at 385 mA. The VGG1 pin is optional and is grounded for nominal operation; a positive voltage there adjusts the quiescent current.

Why use this instead of a higher power part in the family? Because of linearity and simplicity. Fourteen decibels of intercept headroom above compression and no gate sequencing suit instrument and cable products better than 10 dB of headroom and a bias controller.