Contact Us

ADP7104ARDZ-R7

Brand: Analog Devices
Analog Devices ADP7104ARDZ-R7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADP7104ARDZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADP7104ARDZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADP7104ARDZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADP7104ARDZ-R7: 20 V In and 500 mA Out Is a 9 W Regulator Problem in an SOIC Body

The ADP7104 is a low noise CMOS regulator rated 3.3 V to 20 V in, 500 mA out, with 15 uV rms of output noise, 60 dB of rejection at 10 kHz, 350 mV of dropout at full load, a power good output and a programmable undervoltage lockout, in an 8-lead LFCSP or the 8-lead SOIC body this code specifies. The input range and the current rating together produce numbers that the package cannot carry: 20 V to 1.5 V at 500 mA is 9.25 W, and even 12 V to 3.3 V at 500 mA is 4.35 W. This part is right for a high voltage rail feeding a quiet analogue load at a few tens of milliamps, and wrong as a bulk 5 V supply on the same board.

Dissipation is the selection criterion

The 8-lead SOIC has no exposed pad on this variant, so the junction rise comes through the lead frame. A workable rule is to keep the dissipation under about a watt for the SOIC and under two for the LFCSP with a proper pour. From 20 V to 3.3 V that limits the SOIC to about 60 mA, and from 20 V to 15 V it allows about 1 A of theoretical current but the package still caps the load at 500 mA. The 15 uV noise and 60 dB rejection are wasted if the board has to derate the current to a quarter of the rating, so the input voltage should be chosen as low as the rest of the system allows.

Input to outputDissipation at 500 mADissipation at 100 mADissipation at 50 mA
20 V to 15 V2.50 W0.50 W0.25 W
20 V to 5 V7.50 W1.50 W0.75 W
20 V to 3.3 V8.35 W1.67 W0.84 W
12 V to 3.3 V4.35 W0.87 W0.44 W
5 V to 3.3 V0.85 W0.17 W0.09 W

Accuracy, soft behaviour and the lockout pin

Initial accuracy is 0.8 percent, and the tolerance over line, load and temperature is minus 2 percent to plus 1 percent across the full minus 40 C to plus 125 C range, tightening to minus 1.25 percent to plus 1 percent over the 0 C to 85 C range. Quiescent current is 900 uA at 500 mA of load, which is not a micropower figure, so this part belongs on a rail that is always on in a mains powered product rather than in a battery one. The programmable undervoltage lockout is a comparator on the enable pin, so a resistor divider can hold the regulator off until the input is high enough for the downstream circuit, which is a sequencing function usually bought as a separate part.

Noise, the reference bypass and the power good flag

The 15 uV rms figure applies to the fixed output versions and depends on the reference bypass capacitor, which also sets the soft start ramp. The power good output is open drain with a delay that follows the output reaching regulation, so a processor can hold reset until the analogue rail is valid. Seven fixed voltages are available, 1.5 V, 1.8 V, 2.5 V, 3 V, 3.3 V, 5 V and 9 V, plus an adjustable version from 1.22 V to the input minus the dropout, and the adjustable version has a different noise gain so its noise is not the 15 uV printed on the front page.

Matching a high voltage low noise regulator

The substitution question is the maximum input voltage, the thermal path and the noise, in that order, because a 6 V part with better noise is not a replacement in a 20 V socket. The power management cross reference page covers the family, the pin to pin cross reference page covers the footprint, and incoming checks follow the incoming inspection plan.