Contact Us

ADP5300ACPZ-1-R7

Brand: Analog Devices
Analog Devices ADP5300ACPZ-1-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADP5300ACPZ-1-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADP5300ACPZ-1-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADP5300ACPZ-1-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADP5300ACPZ-1-R7: 180 nA at no load, and the two modes that decide the rest of the curve

The ADP5300ACPZ-1-R7 is a step-down regulator built around a quiescent current of 180 nA, which is the figure that decides whether a coin cell or a lithium primary cell survives ten years in a metering or sensing node. The code carries the package (ACPZ is the 10-lead 3 mm by 3 mm LFCSP), a factory option field and the reel suffix. That option field is not cosmetic: the output voltage is selected from 0.8 V to 5.0 V by an external VID resistor together with a factory fuse, so the option in the code has to match the resistor network already on the board.

The input range is 2.15 V to 6.5 V with operation down to 2.0 V, which covers two alkaline cells, a lithium thionyl chloride cell, or a single cell lithium ion pack without a second stage. The regulator runs in either hysteresis mode or PWM mode, chosen by the state of the SYNC/MODE pin at any time during operation.

What the vendor page states

ParameterValue
Input range2.15 V to 6.50 V, operates down to 2.00 V
Quiescent current180 nA, no load
Output voltage0.8 V to 5.0 V, set by VID resistor and factory fuse
Accuracyplus or minus 1.5 percent over temperature in PWM mode
Output currentup to 50 mA in hysteresis mode, up to 500 mA in PWM mode
Switching frequency2.0 MHz typical in PWM, SYNC clock 1.5 MHz to 2.5 MHz
Monitoring and controlVOUTOK flag, STOP pin, separate enable, QOD
Protectionovercurrent, thermal shutdown, input undervoltage lockout
External partsfour small components in total
Package and range10-lead LFCSP 3 mm by 3 mm, minus 40 C to plus 125 C junction

The two modes are two different power supplies

In hysteresis mode the part delivers up to 50 mA with the best efficiency below 1 mW of output, which is the region a sensor node lives in while it sleeps and wakes for a measurement. In PWM mode it delivers up to 500 mA with lower output ripple and 1.5 percent accuracy over temperature, which is the region a radio or a display occupies for a few milliseconds. The pin that selects between them can be driven at run time, so the same regulator covers both ends. What a buyer should not assume is that the 500 mA figure is available in the low power mode, or that the 180 nA figure applies while the part is switching at 2 MHz. They are two operating points of one part, and the datasheet curves are the only place the crossover is defined.

What 180 nA is worth in shelf life

A 225 mAh coin cell drained at 180 nA with no other load runs for about 143 years on paper, against about 9,375 days for a part that leaks 1 microamp. The ratio is 5.6 to one, and in a real node the regulator is rarely the largest term: a leaking capacitor or a pull-up left on a floating input easily exceeds the regulator's own current. That is the reason the STOP pin and the separate enable exist, and the reason a support review of a low power board starts with the pin states rather than the part number.

Ripple, duty cycle and the 2 MHz choice

The 2 MHz switching frequency is a 500 ns period, which allows a small inductor and keeps switching harmonics away from the 433 MHz and 868 MHz receive bands that share these nodes. From 3.6 V in to 0.8 V out the duty cycle is 22 percent, so the inductor carries current for a fifth of each period and the output capacitor carries the rest. Synchronising to an external clock between 1.5 MHz and 2.5 MHz is the option to hold the switching tone at a fixed offset from a radio channel, and the STOP pin is the option to stop switching entirely while a conversion or a receive window is open.

What to confirm before the reel is ordered

The option field has to match the board's VID network, the reel suffix has to match the assembly line's feeder, and the accuracy claim has to be read against the mode the load actually runs in. Where the load profile is not yet fixed, ask for the option that leaves the widest output range available and confirm the VID resistor values in writing.

The wider regulator line is indexed under Analog and mixed-signal ICs, the pin compatible equivalents are in the power management cross reference, and the lead time situation for this family is tracked on the component lead time page.

ADP5300ACPZ-1-R7: the two volt floor, and what the part number's option field commits

The input range is 2.15 V to 6.5 V with operation down to 2.0 V, and that floor is the number to check against the cell chemistry rather than against the nominal voltage. Two alkaline cells start at 3.1 V and end at about 2.0 V under light load, a lithium thionyl chloride cell sits at 3.6 V open circuit and sags under pulse, and a single lithium ion cell runs from 4.2 V to 3.0 V. All three fit the input window and none of them fits it in the same way, because the 180 nA quiescent current is a no load figure and the output current ceiling depends on which mode the part is in: 50 mA in hysteresis mode and 500 mA in PWM mode.

ItemValueWhat it decides
Input floor2.15 V, operating to 2.00 VTwo alkaline cells at end of life sit on the floor, not above it
Quiescent current180 nA at no load1.58 mAh over a year, so a 225 mAh coin cell lasts decades at that rate
Output current50 mA hysteresis, 500 mA PWMThe mode, not the part, sets the load ceiling
Switching2.0 MHz typical in PWMThe inductor and the output capacitor are sized by this frequency
External partsFour small componentsThe whole converter is a two layer footprint
Option fieldOutput set by VID resistor and factory fuseThe code and the resistor network have to match, or the rail is wrong

One hundred and eighty nanoamps against a cell that self discharges

At 180 nA the part removes 1.58 mAh from a cell in a year, which is far below the self discharge of any primary cell, so the quiescent current is not what limits the shelf life. What limits it is the average load: a radio that wakes for 10 ms every 10 s at 20 mA draws an average of 20 uA, which is a hundred times the regulator's own current. The 180 nA figure is therefore a specification that matters only in a product whose average load is a few microamps, and buying it for a node that transmits regularly is buying a number rather than a benefit.

The option in the code is part of the circuit

The output voltage is chosen by a resistor on the VID pin together with a factory programmed fuse, so the option field in the order code and the resistor on the board have to agree. Fitting a resistor that was calculated for a different option gives a rail that is not the one the drawing says, and because the part works, the fault appears later as a marginal supply rather than as a dead board. That is the field to copy from the drawing and confirm against the code on the reel label.

Two modes, one pin, and a decision at run time

The SYNC and MODE pin can be driven while the part is running, so the same regulator serves a sleeping node at 50 mA with the best efficiency below a milliwatt and a transmitting node at 500 mA with 1.5 percent accuracy. The trap is to assume the 500 mA figure comes with the 180 nA figure. The mode that delivers the current has a switching converter running at 2 MHz, and the mode that delivers the quiescent current is the one with limited output. The range this part belongs to is listed on the analog and mixed signal line card, the case where the option in the code has to be matched from another source is under BOM shortage recovery, and reel and date code confirmation is on the lead time page.

Request Quote — In Stock, 100% New & Original, Full Warranty