ADP162ACBZ-1.8-R7
Product Specifications
ADP162ACBZ-1.8-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADP162ACBZ-1.8-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADP162ACBZ-1.8-R7: 560 nA of Quiescent Current in a Four-Ball Package, and No Output Discharge
The ADP162ACBZ-1.8-R7 is a 1.8 V fixed output, 150 mA low dropout regulator in a four-ball wafer level package, and it is the member of its family that draws 560 nA at no load. The input range is 2.2 V to 5.5 V, the dropout is 195 mV at 150 mA in the feature list, and the part is stable with 1 uF ceramic capacitors at both input and output, which is what makes the four-ball package usable at all. The distinction that decides the order code is the output discharge: the ADP160 includes an integrated discharge resistor that pulls the output down when the enable pin is low, and the ADP162 is identical except that it does not. A rail that has to collapse quickly at shutdown therefore needs the ADP160, and a rail that must not be discharged through the regulator, for instance one that is backed up by a supercapacitor or a battery, needs the ADP162 on this page.
What 560 nA means for a battery product
At 560 nA a year is 4.9 mAh, which is negligible against any cell that is expected to last a year. The number that matters more is the over-temperature and maximum figure: the same current is specified at 860 nA over minus 40 to plus 125 degrees and 1250 nA maximum, so the budget should be built from the maximum and not the typical. A 1 uA standby budget for a coin cell product is realistic with this part and impossible with a conventional 50 uA regulator, and that is the entire reason to accept a 150 mA current limit on a rail that may only ever deliver 20 mA. The current limit is not the constraint; the accuracy over temperature is, because the output is specified at plus or minus 1 percent at 25 degrees and plus or minus 3.5 percent over the full range.
Dropout, headroom and the 1.8 V case
The 1.8 V output of this order code needs an input of at least 2.2 V to be inside the specified input range, and the dropout at 150 mA is 195 mV in the feature list, with 120 mV typical and 225 mV maximum over temperature for the 3.3 V case in the dropout table. At a 2.2 V input the part has 400 mV of headroom to a 1.8 V output, which is inside the dropout budget at full load but not by much, so a battery that sags to 2.1 V takes the regulator out of regulation before the cell is exhausted. Dissipation is small at these levels: 1.8 V at 150 mA from 3.3 V is 225 mW, and from 2.5 V it is 105 mW, so the four-ball package is limited by the board copper rather than by the silicon.
| Parameter | Value on this order code | What it decides |
|---|---|---|
| Output | 1.8 V fixed | The family covers 1.2 V to 4.2 V in 15 options |
| Current | 150 mA maximum | Enough for a sensor node, not for a radio power stage |
| Quiescent current | 560 nA typical, 860 nA over temperature, 1250 nA max | 4.9 mAh a year at the typical figure |
| Shutdown current | Less than 50 nA typical | Storage current is set by the load, not the regulator |
| Input range | 2.2 V to 5.5 V | A 1.8 V output has 400 mV of headroom at 2.2 V |
| Dropout | 195 mV at 150 mA in the feature list | 120 mV typical, 225 mV maximum at 3.3 V |
| Accuracy | Plus or minus 1 percent at 25 degrees | Plus or minus 3.5 percent over the full range |
| Output discharge | Not fitted on the ADP162 | The ADP160 is the version with the discharge resistor |
| Package | 4-ball WLCSP, 0.5 mm pitch | No thermal pad, the balls are the heat path |
Noise, rejection and the rail it sits on
Supply rejection is 72 dB at 100 Hz, which falls with frequency like every LDO, so a switching converter in front of this part has to have its ripple filtered before the regulator rather than after it. Output noise is low enough that the part is used directly as an analogue supply in portable instruments, and the 1 uF ceramic output capacitor is part of that noise performance and not an optional extra. The enable pin is a logic input with a defined threshold, and because the ADP162 has no discharge resistor, a rail that is disabled while the load still holds charge will stay up until the load discharges it, which in a mixed supply system can keep a processor alive after the software believes it has shut the rail down.
Where the part fits
Portable medical devices, battery instruments, post regulation after a switching converter and always-on housekeeping rails in equipment that runs from a cell are the intended sockets. Where the input can fall below 2.2 V a different topology is needed, and where the rail has to be actively discharged at shutdown the ADP160 is the correct order code. The ADI part second source page lists the fields a substitute has to match, the pin to pin cross reference covers the four-ball body, and the one stop BOM sourcing page covers the power chain on one order.