Contact Us

ADM485JRZ-REEL7

Brand: Analog Devices
Analog Devices ADM485JRZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADM485JRZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADM485JRZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADM485JRZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADM485JRZ-REEL7: a 5 Mbps RS-485 and RS-422 transceiver with a 19 V common mode window

What this order code is

ADM485JRZ-REEL7 is a single 5 V differential line transceiver that meets EIA RS-485 and RS-422. It contains one driver and one receiver that can be enabled independently, both tristated when disabled, and it is built on a BiCMOS process that pairs CMOS quiescent current with the switching speed of bipolar output devices. The published data rate is 5 Mbps, the bus common mode range is minus 7 V to plus 12 V, and up to 32 transceivers can share one bus with only one driver enabled at a time. The J suffix is the commercial temperature grade, R is the SOIC body, Z is the lead free finish and REEL7 is the reel option.

The feature that keeps this part in long life industrial bills of materials is the behaviour when it is unpowered. The driver outputs go to a high impedance state with the supply off and stay high impedance across the whole minus 7 V to plus 12 V common mode range, so a board can be removed from a live bus without loading it. A thermal shutdown circuit forces the driver into the same high impedance state when a fault raises the die temperature, which covers the two faults that actually happen in the field: a shorted bus and two drivers enabled at once.

Parameters as published

ItemValue
StandardEIA RS-485 and RS-422
Data rate5 Mbps
Supplysingle 5 V
Bus common mode rangeminus 7 V to plus 12 V
Nodes on one busup to 32 transceivers
Driver propagation delay10 ns
Receiver propagation delay15 ns
Receiver fail safelogic high on unconnected inputs
Protectionthermal shutdown, short circuit, latch up guard
Outputs when unpoweredhigh impedance
Body8 lead SOIC, DIP also available
Temperature rangecommercial grade on this suffix

Numbers that decide the application

At 5 Mbps a bit is 200 ns wide. The driver delay of 10 ns and the receiver delay of 15 ns add to 25 ns for a round trip through one repeater pair, which is 12.5 percent of a bit, and that is the number to compare against the timing budget of a half duplex protocol with a turnaround. A slow opto-isolated stage in front of the transceiver costs far more of the bit than the transceiver itself, which is why isolated RS-485 nodes are usually specified at 1 Mbps or lower while the plain part is rated at 5.

The common mode window is 19 V wide and it is the reason an RS-485 link survives a plant where the two ends sit on different ground references. A 12 V difference between node grounds is inside the window and the receiver still reads the differential signal; a 25 V difference is outside it and no amount of twisted pair helps. The receiver input resistance for a unit load is what allows 32 nodes: 32 unit loads in parallel is 375 ohm against the 60 ohm that two 120 ohm terminators present, so the termination dominates the load and the node count does not change the differential level much.

The fail safe wording needs to be read exactly. The receiver goes to a logic high output when its inputs are unconnected, that is, floating. It does not follow that the same happens on a bus that is terminated at both ends but has no driver enabled, because the 120 ohm resistors pull the pair together and the differential voltage is zero. A protocol that uses an idle bus as a mark state needs bias resistors that hold a few hundred millivolts across the pair, and that bias is not in this part.

Where it fits and where it does not

It fits plant floor networks, motor drives, meters, building controls, long sensor runs and any point to point or multipoint link that has to survive a ground offset. It does not fit a 3.3 V only board without attention to the receive side, because the RXD output swings to 5 V and a 3.3 V microcontroller pin that is not 5 V tolerant will not take it, and it does not fit an isolated port without adding a digital isolator. The 5 Mbps rate is the ceiling for the whole cable, not per node, and a 1 km run at 5 Mbps is outside the standard even though the transceiver is willing.

Supply and second source questions

The questions that come back on this code are about temperature grade, ESD level and the isolated variant. This code is the plain commercial part; the family also lists members with enhanced ESD protection and members in the wider temperature grades, and those are separate order codes rather than options on this one. A cross reference that matches the function and the pinout can still differ in ESD rating and temperature, which is exactly the kind of difference that only appears in a qualification test. The parts that share the pinout and the ones that only look similar are listed on the ADI part second source page.

Sourcing notes and next step

We quote this code against the bill of materials and check the four fields that decide whether the line runs: temperature grade, ESD level, body and packing. Where the exact code is short we will say so rather than move the line to a different grade without telling the buyer. Send the line items, quantities and required date through the BOM shortage recovery page, and if the board is a long life industrial one, the alternative route for parts that are still in production but no longer recommended for new builds is the obsolete part cross reference hub. The interface family list sits on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty