ADM2483BRWZ
Product Specifications
ADM2483BRWZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM2483BRWZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADM2483BRWZ: isolated RS-485 with true fail safe receiver inputs
The ADM2483BRWZ is the member of the isolated RS-485 family that specifies true fail safe receiver inputs and thermal shutdown on top of the 500 kbps isolated transceiver. It is quoted where a bus can be idle, unplugged or shorted and the receiver still has to deliver a defined level rather than noise.
Published values
| Parameter | Value |
|---|---|
| Function | isolated half duplex RS-485 transceiver |
| Data rate | 500 kbps |
| Isolation test voltage | 2500 V rms for one minute |
| Working voltage | 565 V peak |
| Receiver | true fail safe on open, shorted and terminated but undriven bus |
| Protection | thermal shutdown and current limiting |
| Supply current | 2.5 mA maximum |
| Input impedance | 96 kohm |
| Package and range | 16-lead wide body SOIC, -40 C to +85 C |
What true fail safe actually fixes
A receiver with a threshold at zero volts will output whatever the noise on the bus happens to be when no driver is talking. In a protocol that uses an idle line to mean a break or a start condition, that noise becomes a stream of framing errors and the software spends its time resynchronising.
True fail safe moves the threshold so that an open bus, a shorted bus and a terminated but undriven bus all produce a defined high output. The price is a small loss of differential noise margin, which is why the property is specified for those three conditions rather than universally.
Thermal shutdown and the fault that causes it
A driver that is enabled into a shorted bus delivers its short circuit current continuously. The ADM2483 limits the current and shuts the driver down when the junction temperature rises, then restarts when it falls. Without that behaviour the package, not the fault, decides the outcome.
On a bus where two nodes are both enabled by a software fault, the same protection saves the transceivers. The fault still has to be found, but it is a protocol problem rather than a replacement of two parts.
The working voltage against the test voltage
565 V peak of working voltage is 400 V rms, which suits a 400 V drive and does not suit a 690 V one. The 2500 V rms figure is the one minute test, and it is the number that appears on data sheets that do not separate the two.
For a safety case the working voltage and the pollution degree decide the barrier, and the test voltage only proves the barrier was built. A buyer comparing two isolated parts on the test voltage alone can choose the part with the lower continuous rating.
Replacement checks
The 16-lead members of this family differ in data rate, working voltage, duplex and fail safe behaviour, and the pin out is shared within the package size. A substitute has to match the working voltage, then the fail safe behaviour, then the bus side supply.
The pages below hold the family cross reference, the acceptance sequence and the delivery options for a part on allocation.
Where a customer needs a second position on this part, the pin to pin cross reference is the starting point, the ADI second source page sets out the checks a substitution has to pass, and component lead time solutions is the short lead time route we quote against.
Two questions buyers ask
Why does a bus need fail safe if it is always driven? Because a bus is not always driven. Between frames, during a node reset and while a cable is unplugged, the receiver sees an undriven pair, and its output during that interval is what the protocol has to interpret.
Can the isolated side share a ground with the logic side? No. The barrier exists to separate them. Sharing a ground defeats the isolation and leaves the common mode transient to travel through the board instead of through the barrier.