ADG802BRTZ-500RL7
Product Specifications
ADG802BRTZ-500RL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG802BRTZ-500RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG802BRTZ-500RL7: a normally closed switch with 0.4 ohm at 125 C
The ADG802 is a single pole single throw CMOS switch that is normally closed, with a maximum on resistance of 0.4 ohm at 125 C and 0.08 ohm of maximum flatness at the same temperature. The order code reads B for the silicon revision, RT for the six lead SOT-23 body, Z for RoHS and 500RL7 for the 500 unit reel. Its twin, the ADG801, is the normally open version, and the two are pin compatible with the ADG701 and ADG702 respectively, which is the detail that decides most substitutions: the pin out is the same, the state at power up is not.
What the vendor page states
| Parameter | Value |
|---|---|
| Configuration | single pole single throw, normally closed |
| On resistance | 0.25 ohm typical, 0.4 ohm maximum at 125 C |
| On resistance flatness | 0.08 ohm maximum at 125 C |
| Supply | 1.8 V to 5.5 V single |
| Current carrying | 400 mA |
| Switching time | 35 ns |
| Logic | TTL and CMOS compatible input |
| Temperature | minus 40 C to plus 125 C, automotive range |
| Packages | 6-lead SOT-23 and 8-lead MSOP |
| Compatibility | pin compatible with the ADG702 |
Normally closed is a power up decision, not a detail
A switch that is closed with no supply applied defines the state of the circuit before the processor has booted. In a signal path that is what you want if the default has to be a connected route, for example a bypass around a stage that is only inserted on demand. In a power path it is the opposite: a normally closed switch means the load is live as soon as the rail comes up, whatever the firmware intends. Read the family round the right way: the ADG801 is normally open, this part is normally closed, and the two share a land pattern.
0.4 ohm at 125 C is the number to quote, not 0.25 ohm
The typical figure of 0.25 ohm is measured at room temperature. At 125 C the guaranteed maximum is 0.4 ohm, and at 400 mA that is 160 mV of drop and 64 mW of dissipation, against 100 mV and 40 mW at the typical value. In a 5 V system the 160 mV is 3.2 percent of the rail, which is the figure a load has to tolerate. The flatness number follows the same rule: 0.08 ohm at 125 C across a 100 mA signal is 8 mV of change, and that is what shows up as distortion if the switch carries an analogue signal rather than a dc current.
35 nanosecond switching and why it matters here
A 35 ns switching time lets the part replace a small relay in anything that switches at a human rate or faster, and it also means the control pin has to be treated as a digital line with a defined state, not left floating. The 1.8 V to 5.5 V single supply range matches a 3.3 V processor pin directly, and the TTL and CMOS compatible input removes the level translator that a relay driver would need. In a battery powered instrument the absence of a coil current is the larger gain: the switch draws essentially nothing when static.
Where the part is used
The vendor lists power routing, battery powered systems, data acquisition, communications and relay replacement, which is the same list every small CMOS switch carries; the difference is the 0.4 ohm at temperature and the 400 mA rating. Those two numbers put it in the category of switches that can carry a load current rather than only a signal, and that is where the normally closed default is worth thinking about twice. The pin to pin cross reference lists the normally open twin and the older parts it replaces, the BOM shortage recovery page covers the cross for the six lead land, and the analog and mixed signal category page holds the rest of the switch family.
Request Quote — In Stock, 100% New & Original, Full Warranty