ADG721BRMZ-REEL7
Product Specifications
ADG721BRMZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG721BRMZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG721BRMZ-REEL7: A Dual SPST Switch with 4 ohm On Resistance from 1.8 V to 5.5 V
What this part is
The ADG721 is a pair of independent single pole single throw switches in complementary metal oxide semiconductor, both normally open, in an eight lead MSOP. On resistance is 4 ohm maximum at 5 V and 10 ohm maximum at 3 V, flatness is low enough that the part does not add measurable distortion to a signal path, and the minus three decibel bandwidth is above 200 megahertz. Switching times are 20 nanoseconds on and 10 nanoseconds off, and the static power is under 0.1 microwatt.
The family has three members that differ only in the rest state: the ADG721 is normally open on both switches, the ADG722 normally closed on both, and the ADG723 is normally open on one and normally closed on the other, which gives it break before make action. The supply range of 1.8 V to 5.5 V is what makes the part useful next to a modern converter, because the switch can sit on the same rail as the digital side without a second supply. Applications listed are USB 1.1 signal switching, mobile handsets, personal digital assistants, battery powered instruments, sample and hold circuits, audio routing, video switching and reed relay replacement.
Published figures that matter to a buyer
| Configuration | 2 independent SPST, normally open |
| Supply | 1.8 V to 5.5 V single |
| On resistance at 5 V | 4 ohm maximum |
| On resistance at 3 V | 10 ohm maximum |
| Bandwidth | above 200 MHz at minus 3 dB |
| Turn on time | 20 nanoseconds |
| Turn off time | 10 nanoseconds |
| Static power | below 0.1 microwatt |
| Control levels | TTL and CMOS compatible |
| Bodies | 8 lead MSOP and 3 mm by 2 mm LFCSP |
| Family variants | ADG722 normally closed, ADG723 one of each with break before make |
Where the headline numbers stop
Four ohms is a 5 V number and ten ohms is the 3 V number, a factor of 2.5 for the same die. In a path that drives a 1 kohm load, 4 ohm is 0.40 percent of gain error at 5 V and 1 percent at 3 V; into a 10 kohm load the same resistances are 0.040 and 0.100 percent. That is why the part is comfortable in a 12 bit path and marginal in a 16 bit one: the error is a ratio of the switch resistance to the load, so the load decides whether the switch is transparent.
Static power below 0.1 microwatt is 20 nanoamps at 5 V, which is small enough that the switch can stay powered in a product that sleeps. The dynamic side is not free: the charge that moves in and out of the gate capacitance at every transition has to come from the control pin, so a control line driven at high frequency costs more than the quiescent figure suggests. At 20 nanosecond turn on, a control signal at 1 MHz would be asking the switch to settle in a twentieth of its period, which is not a useful operating point.
Two hundred megahertz of bandwidth is a small signal number and says nothing about what the switch does to a fast edge. The part is a resistive element in series with the signal, and at the top of its band the package and the board parasitics dominate. A board that uses the 3 mm by 2 mm body has a shorter path than one that uses the MSOP, which is why the smaller body is offered in the A grade.
Applications where it fits
- Signal routing in handheld instruments where a mechanical relay is too large and too slow.
- Sample and hold circuits and multiplexed sensor inputs on a single low voltage rail.
- Audio and video path selection in consumer and portable equipment.
- USB 1.1 signal switching and battery powered accessories.
- Calibration paths where a switch has to insert a reference without a second supply rail.
Two questions buyers ask
Which family member has break before make? The ADG723, which is normally open on one switch and normally closed on the other. The ADG721 and ADG722 are both switches in the same rest state, so they make before break if they are used to change over a signal. A changeover function built from the wrong member produces a short between two sources during the transition.
Is the LFCSP a drop in for the MSOP? No. The 3 mm by 2 mm body is a different footprint with a different pad pattern, and it is offered in the A grade. The two are the same die in different packages, so the substitution is an assembly change and not a stock swap.
Sourcing notes and next step
ADG721BRMZ-REEL7 is the eight lead MSOP in tape and reel. The order code carries the rest state in the root number and the body in the letter code, so a quotation for ADG722 or ADG723 is a different behaviour and not a different price on the same part. The analog and mixed signal IC family page lists the switch line, the pin to pin cross reference page covers what a switch substitution has to match beyond the pinout, and the BOM shortage recovery page sets out the options when a specific rest state is not on the shelf.
Request Quote — In Stock, 100% New & Original, Full Warranty