ADG707BRUZ-REEL7
Product Specifications
ADG707BRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG707BRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG707BRUZ-REEL7: eight differential channels on a 1.8 V rail with 2.5 ohm of on resistance
The ADG707BRUZ-REEL7 is an Analog Devices differential 8-to-1 CMOS multiplexer in a 28-lead TSSOP, the differential half of a pair whose single-ended member is the 16 channel ADG706. Supply range is 1.8 V to 5.5 V single or plus or minus 2.5 V dual, on resistance is 2.5 ohm with 0.5 ohm of flatness, leakage is 100 pA, switching time is 40 ns, and the inputs are TTL and CMOS compatible. Three address lines A0, A1 and A2 select the channel, an EN pin disables the part and turns all channels off, and every channel exhibits break-before-make action so two inputs are never shorted together during a change. The same part works as a multiplexer or a demultiplexer because the switches are bidirectional. It is on the analog and mixed-signal IC line card.
Eight differential channels means sixteen single-ended paths in one package
A differential 8-to-1 switch is a 16-to-2 switch in single-ended terms, so one part carries as many signal paths as two 8 channel single-ended parts. That is the reason to use it in a differential acquisition front end: the two halves of each pair are switched together, the matching between them is a property of one die, and the channel to channel skew that two separate packages would introduce does not exist. Break-before-make then guarantees that the positive and negative inputs of two channels are never bridged during the change.
| Parameter | Vendor figure | Derived figure |
|---|---|---|
| Configuration | differential 8 to 1 | 16 single-ended paths, 3 address lines |
| Supply | 1.8 V to 5.5 V single, plus or minus 2.5 V dual | 3.1 to 1 span, runs from a coin cell rail |
| On resistance | 2.5 ohm | 2.5 mV per mA of signal current |
| Flatness | 0.5 ohm | 20 percent of the on resistance over the signal range |
| Leakage | 100 pA | 100 uV into a 1 Mohm source |
| Switching time | 40 ns | 4 percent of a 1 us channel slot |
| Package | 28-lead TSSOP | 8 differential channels in a 9.7 mm body |
Flatness, not the headline resistance, sets the distortion
0.5 ohm of flatness across a 2.5 ohm switch is a 20 percent change in resistance as the signal moves, and a switch in series with a load forms a divider whose ratio moves with the signal. Into a 1 kohm load the gain changes by 0.05 percent over the signal range, which is minus 66 dB of second harmonic distortion. Into a 10 kohm load the same flatness is 0.005 percent and minus 86 dB. The load impedance is therefore as much a part of the distortion specification as the switch itself, and a buffer with a high input impedance behind the multiplexer is what makes the part look linear.
Selection notes
- The 1.8 V minimum supply allows the multiplexer to share a rail with a low voltage converter, which removes a level shifter from the control lines.
- Leakage of 100 pA is specified at room temperature; it rises with temperature, and a 1 Mohm source impedance turns it into a voltage that has to be budgeted.
- Dual plus or minus 2.5 V operation allows a signal that swings below ground, which a single supply part cannot pass.
- The EN pin puts all channels in the off state, so several multiplexers can share a common output bus without an external switch.
Questions buyers ask
Can the ADG707 replace two single-ended 8 channel parts? Yes, if the source is differential, and the board then has one package and one set of address lines instead of two. If the sources are single-ended, the ADG706 is the part to use.
Does 2.5 ohm rule it out in front of a 16-bit converter? The resistance itself does not, because the converter input is high impedance. The leakage and the flatness do, and both are bounded in the table above.
Multiplexer substitutions are compared on pin to pin cross reference, and the arithmetic for a lower cost equivalent with the same function is on how to reduce component cost.
Request Quote — In Stock, 100% New & Original, Full Warranty