Contact Us

ADG506AKRZ

Brand: Analog Devices
Analog Devices ADG506AKRZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG506AKRZ — Analog & Mixed-Signal ICs | Superb Automation

ADG506AKRZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG506AKRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG506AKRZ: 16-channel analog multiplexer with 20 pA leakage

The ADG506AKRZ switches one of sixteen inputs to a common output from four address lines and an enable input, in a 28-lead SOIC. It works from a 10.8 V to 16.5 V single supply or the equivalent split supply, takes a signal over the full VSS to VDD range, and dissipates at most 28 mW. Leakage is 20 pA typical, which is what makes sixteen channels practical on one output.

Published values

ParameterValue
Configuration16 to 1 single ended multiplexer
Addressing4-bit binary plus enable
Supply range10.8 V to 16.5 V single or split
Analog signal rangeVSS to VDD
Maximum supply rating44 V
Leakage current20 pA typical
Power dissipation28 mW maximum
LogicTTL and 5 V CMOS compatible
Temperature range-40 C to +85 C in the plastic package
Replacement forDG506A and HI-506, per the vendor
Packages28-lead DIP, SOIC, PLCC, TSSOP and LCCC

Sixteen channels on one output

Sixteen off channels each contribute their leakage to the common output. At 20 pA typical that is 300 pA of total leakage, which into a 1 Mohm load is 0.3 mV and into a 10 Mohm load is 3 mV. The channel count is therefore limited by the load impedance rather than by the switch, and a high impedance scanner needs a buffer close to the multiplexer rather than at the end of the cable.

The four address lines plus an enable give 32 states in a 5-bit word, and the enable allows a bank of multiplexers to share one output. A 64 channel system is four of these with a decoder on the enable lines, which is the architecture the part was built for in test equipment and process control.

The 10.8 V to 16.5 V window

The supply range is narrow compared with the 44 V absolute maximum: the part is specified from 10.8 V to 16.5 V, so a 12 V rail at plus or minus 10 percent is inside it and a 15 V rail is inside it, but a 5 V system is not. A 24 V industrial rail is also outside, and a board that runs at 24 V needs a regulator for the multiplexer or a different part.

The 44 V maximum rating is the transient and fault limit, not an operating point. A 24 V rail with a transient to 30 V does not damage the device, but the on resistance and the switching times at that supply are not specified and the channel cannot be qualified against them.

28 mW and the plastic temperature range

Twenty-eight milliwatts maximum is the whole device, so a 16 channel scanner adds less heat than a single logic gate on some boards. The plastic package is specified from -40 C to +85 C, which is the industrial range rather than the automotive one, and the ceramic and LCCC bodies carry the wider range for military use.

The on resistance of the switch is not 100 ohm like the 44 V family: at this supply the FET is different and the resistance has to be read from the table at the supply actually used. A channel that is calibrated at 15 V and then run at 12 V changes its gain error, and that is the kind of shift a multiplexed instrument shows when it is powered from a battery rather than a bench supply.

Two pages worth reading before a purchase order goes out are the obsolete part cross reference hub and one stop BOM sourcing; the first lists what else fits the socket, the second is the test sequence for a drop in, and component lead time solutions covers the case where the shortage is already on the line.

Two questions buyers ask

Does the ADG506AKRZ work on a 5 V supply? No. The specified range is 10.8 V to 16.5 V, so a 5 V system needs a different multiplexer. The 44 V figure is an absolute maximum, not an operating range.

Can it replace a DG506A? The vendor lists it as a superior alternative and the pinout follows the same 28-lead arrangement. The on resistance and the leakage differ, so the channel calibration has to be repeated after the change.