ADG408BRZ
Product Specifications
ADG408BRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG408BRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG408BRZ: 8-channel multiplexer in a 16-lead SOIC with 100 ohm switches
The ADG408BRZ is the 16-lead SOIC body of the eight channel multiplexer. The die is the same as the TSSOP order code, so the 100 ohm maximum on resistance, the under 75 uA supply current and the 44 V supply rating carry across; what changes is the lead frame, the board area and how easy the part is to probe. It switches one of eight inputs to a common output from three address lines, with an enable input that turns every channel off.
Published values
| Parameter | Value |
|---|---|
| Configuration | 8 to 1 single ended multiplexer |
| On resistance | 100 ohm maximum |
| Supply range | up to 44 V total |
| Analog signal range | VSS to VDD |
| Supply current | less than 75 uA |
| Off isolation | specified in the data sheet at 100 kHz |
| Charge injection | low, quoted for the digital input transition |
| Switching | break before make |
| Addressing | 3-bit binary plus enable |
| Logic | TTL and CMOS compatible |
| Package | 16-lead SOIC_N |
SOIC against TSSOP on the same die
The wider body has a longer lead frame between the pin and the die, which raises the lead inductance and lowers the thermal resistance. At the currents this part handles neither matters for the signal, and the real difference is mechanical: the SOIC is easier to clip a probe onto during bring up, and it survives more rework cycles than a 0.65 mm pitch TSSOP.
A board that has already qualified the TSSOP and needs a second source should not treat the SOIC as the same line item. The footprint is different, the paste stencil is different and the reflow profile is different, even though the electrical table is shared.
Leakage is what limits the channel count
An off channel is not an open circuit, it is a high resistance. The leakage of the switches adds to the leakage of the following buffer and to the leakage of the board, and a 1 Mohm source converts a nanoamp of leakage into a millivolt of error. Eight channels on one output therefore multiply the leakage paths, and the error appears as a channel to channel offset rather than as noise.
The usual cure is to keep the source impedance low, or to buffer each channel before the multiplexer. A thermocouple with a 10 kohm lead resistance is comfortable; a pH electrode with a 100 Mohm source is not, and that channel needs its own amplifier ahead of the switch.
Supply headroom and the 44 V rating
A 44 V total supply rating means a plus or minus 22 V split or a 44 V single rail, and the analog signal can swing to both rails. A plus or minus 15 V signal path is therefore inside the part with 7 V of headroom at each end, which is the margin that keeps a transient from forward biasing the substrate.
Under 75 uA at any supply in that range means the multiplexer does not appear in the power budget. That is what allows it to be used in a loop powered instrument where the whole board has 4 mA, and it is also why the part runs cool in a sealed enclosure.
For a board that has to keep running while a reel runs out, the obsolete part cross reference hub is where the family alternatives sit, one stop BOM sourcing is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.
Two questions buyers ask
Can the ADG408BRZ and the ADG408BRUZ be used on the same board? Not on the same footprint. The BRZ is a 16-lead SOIC and the BRUZ is a 16-lead TSSOP, and the two bodies are not interchangeable without a board change even though the electrical table is shared.
How many address lines does it need? Three, A0 to A2, plus an enable. The enable turns all eight channels off, which is what allows several devices to share a common output line.