ADG408BRUZ
Product Specifications
ADG408BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG408BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG408BRUZ: 8-channel analog multiplexer in a 16-lead TSSOP
The ADG408BRUZ switches one of eight single ended inputs to a common output under the control of three address lines and an enable input. It is built on an LC2MOS process, has a 100 ohm maximum on resistance, draws under 75 uA and takes supplies up to 44 V with the analog signal range reaching both rails. The RU suffix is the 16-lead TSSOP body, which is the surface mount option for a board that has to scan eight sensors in a small area.
Published values
| Parameter | Value |
|---|---|
| Configuration | 8 to 1 single ended multiplexer |
| On resistance | 100 ohm maximum |
| On resistance flatness | specified over the analog signal range |
| Supply range | up to 44 V total |
| Analog signal range | VSS to VDD |
| Supply current | less than 75 uA |
| Switching | break before make |
| Addressing | 3-bit binary, A0, A1, A2, plus an enable input |
| Logic | TTL and CMOS compatible |
| Replacement for | DG408, pin compatible |
| Package | 16-lead TSSOP |
100 ohm in series with the source
The on resistance is part of the signal path, so a 10 kohm source and a 100 ohm switch form a divider whose ratio changes with the switch resistance. Into a high impedance load that is a gain error of one percent, which is fine for a 10-bit channel and too much for a 16-bit one. Into a 10 kohm load the divider is 1:1 and the error is a factor of two, which is why the following stage has to be a buffer with an input impedance well above the source.
The resistance also drifts with temperature and with the applied signal, so the flatness figure matters as much as the absolute value. A multiplexer that is 100 ohm at mid rail and 130 ohm at the rail produces a distortion term that a dc measurement never shows and an ac measurement always does.
Break before make and the settling question
The switch opens the old channel before it closes the new one, so two sources are never connected together. The price is a moment when the output is open, and the load capacitance holds whatever charge was on it. A channel that switches from 5 V to 0 V and settles into a 12-bit converter needs the buffer to recover from that step, and the recovery time is usually longer than the multiplexer switching time.
Under 75 uA of supply current means the part adds almost nothing to the power budget, which is what makes an eight channel scanner practical in a battery instrument. The 44 V supply rating and the rail to rail signal range mean a plus or minus 15 V signal can pass without a divider, which is unusual in a part this small.
TSSOP against the wider bodies
The same die is offered in a 16-lead TSSOP, a 16-lead SOIC and a 16-lead DIP. The TSSOP is the smallest and the one to take when the board is dense; the SOIC is easier to probe and to rework; the DIP is for a socket. The electrical table is shared, so the choice is mechanical and not a performance decision, but the footprint is different and a board cannot take one for the other.
An enable input that turns all channels off is what allows eight scanners to share one bus: only the device that is addressed drives the line, and the rest present an open circuit. That is the same function an address decoder performs in a memory bus, and it is why the part needs no external logic.
The pages that answer this most often are the obsolete part cross reference hub for the family alternatives, one stop BOM sourcing for the acceptance test, and how to verify a drop in replacement for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Is the ADG408BRUZ a drop in for a DG408? The vendor lists it as a pin compatible replacement, so the footprint and the control lines match. The on resistance and the switching times are not identical, so a channel that was tuned around the DG408 has to be re-measured rather than assumed.
What happens when the enable input is high? All channels are off, whichever address is present. That is the state to use when several multiplexers share a common output, because only the enabled device drives the line.