Contact Us

ADG1419BRMZ

Brand: Analog Devices
Analog Devices ADG1419BRMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1419BRMZ — Analog & Mixed-Signal ICs | Superb Automation

ADG1419BRMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1419BRMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG1419BRMZ: 2.1 Ohm On Resistance With 0.5 Ohm of Flatness at 25 C

The ADG1419 is a single pole double throw switch built on an industrial CMOS process, with a typical on resistance of 2.1 ohm, a maximum of 2.4 ohm at 25 C, and a maximum on resistance flatness of 0.5 ohm. It is specified at plus and minus 15 V, at +12 V and at plus and minus 5 V, accepts 3 V logic levels with a 2.0 V high threshold and a 0.8 V low threshold, and needs no separate logic supply. It handles up to 390 mA of continuous current and switches with break before make action, which is what makes it usable in a multiplexer position where two channels must never be joined.

Why flatness matters more than the absolute value

An on resistance of 2.1 ohm is only a number until it is placed in series with a load. Into a 1 kohm load it is a 0.21 percent gain error, which is small; into a 50 ohm load it is 4 percent, which is not. What makes the part linear is the flatness: 0.5 ohm of variation across the signal range is 0.24 percent of a 1 kohm load, and that variation is what produces distortion, because the switch resistance changes with the signal voltage and modulates the divider. A part with 4 ohm of resistance and 0.5 ohm of flatness is more linear than one with 1 ohm of resistance and 1.5 ohm of flatness, and data sheets that quote only the typical resistance hide exactly this.

Break before make and the 15 ns transition

Break before make guarantees that the first channel opens before the second closes, which prevents two sources from being connected together during a channel change. The transition time is 15 ns maximum at the dual supply ratings, and the enable pin adds a larger delay, 145 ns maximum on the +12 V single supply table. In a multiplexer that switches between two sensors, the break before make interval is the time during which neither channel is connected, and an amplifier behind the switch sees an open input for that interval, so its settling time is added to the switching budget.

ParameterValueWhat it decides
ConfigurationSingle pole double throwTwo to one selection with one control line
On resistance, typical2.1 ohm0.21 percent into 1 kohm, 4 percent into 50 ohm
On resistance, maximum2.4 ohm at 25 CThe number to use for a worst case budget
Flatness, maximum0.5 ohmSets the distortion in a divider
Continuous current390 mAAbove most signal switching requirements
Supply ratingsPlus and minus 15 V, +12 V, plus and minus 5 VSpecified, not merely tolerated
Logic thresholds2.0 V high, 0.8 V lowDriven directly by 3 V logic
Logic supplyNone requiredOne rail fewer on the board
Transition time15 ns maximum at dual supplyShort compared with an amplifier's settling
Enable time145 ns maximum at +12 VThe enable pin is the slower path
Charge injection13 pC13 mV step into a 1 nF hold capacitor
Off isolation-64 dB at 1 MHz0.06 percent of the off channel reaching through
Crosstalk-64 dB at 1 MHzSet by the package and the board, not the die

Charge injection and the hold capacitor

A charge injection of 13 pC into a 1 nF hold capacitor is a 13 mV step at the moment the switch opens. Into a 10 pF capacitor the same charge is 1.3 V, which is why a sample and hold built on a switch of this class needs a buffer and a capacitor chosen against the injection rather than against the acquisition time alone. The injection is roughly independent of the signal, so it appears as a fixed offset in a sampled system and can be subtracted, while the part of it that does vary with the signal appears as distortion.

Single supply and the rail to rail range

The switch passes signals from rail to rail, and the on resistance curve is specified over the full analog input range rather than at one point. On a single +12 V supply the resistance profile rises near the rails, so a signal that swings to within a volt of either rail sees a higher and less flat resistance than one centred at mid supply. That is the reason the part is specified at three supply conditions: the flatness figure belongs to a particular operating point, and a board that runs at a different rail has to look at the corresponding column.

Procurement for a switch in a signal path

Switches are usually bought as part of a signal chain, and the parameters that decide a substitution are on resistance, flatness, charge injection and the supply ratings, not the pin count alone. A part with the same footprint and a wider flatness changes the distortion of the stage behind it. Availability is tracked through one stop BOM sourcing, and the wider question of consolidating a mixed analog bill of materials is set out in BOM consolidation. Where the original code is short, the options are in component lead time solutions.