ADG1404YRUZ
Product Specifications
ADG1404YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1404YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1404YRUZ: a 4 to 1 multiplexer with 1.5 ohm on resistance and 400 mA of continuous current
The ADG1404YRUZ is the low resistance member of the iCMOS multiplexer family: four channels to one, 1.5 ohm on resistance, 2.6 ohm maximum over temperature, 0.3 ohm flatness and 0.1 ohm match between channels. It carries up to 400 mA continuously, is fully specified at plus or minus 15 V, +12 V and plus or minus 5 V, and needs no logic supply.
Published values
| Parameter | Value |
|---|---|
| Configuration | 4 to 1 multiplexer, single ended |
| On resistance | 1.5 ohm typical, 2.6 ohm maximum over temperature |
| Flatness | 0.3 ohm |
| Channel match | 0.1 ohm |
| Continuous current | up to 400 mA |
| Supply | plus or minus 15 V, +12 V or plus or minus 5 V |
| Logic | 3 V compatible, no VL supply required |
| Package | 14-lead TSSOP or 16-lead 4 mm x 4 mm LFCSP |
The current rating is what separates this part from a signal multiplexer
Most 4 to 1 multiplexers are specified for a few tens of milliamps and their on resistance is quoted at a milliamp of test current, which says nothing about what happens at 400 mA. This part publishes both: 1.5 ohm typical at a 10 mA test current and a continuous current rating of 400 mA. At that current the 2.6 ohm maximum over temperature drops 1.04 V and dissipates 416 mW in the package, so the thermal path, not the silicon, is the limiting element.
That makes the part usable for switching a load rather than only a signal: a current shunt range change, a redundant supply selection, a transducer excitation path. It is not a relay replacement for an inductive load with a stall current, but it is a real switch for a resistive load that draws hundreds of milliamps.
Flatness of 0.3 ohm on a measurement path
When the switch is in series with a shunt, the resistance error is not the problem, its variation is. A 0.3 ohm window over the full analog range on a 1.5 ohm switch is a 20 percent modulation of the series resistance, and if the shunt is 10 milliohms the switch is 150 times the shunt and the measurement is meaningless. The part belongs on the voltage sensing side of a shunt, where the current is microamps, or on a path where the load is at least a few hundred ohms.
On a 600 ohm load, 1.5 ohm is 0.25 percent and 0.3 ohm of flatness is 0.05 percent, which is a distortion term well below the resistor tolerance. That is the regime where the low resistance is bought for headroom rather than for accuracy.
Supply flexibility
The same order code is specified at plus or minus 15 V, at +12 V single and at plus or minus 5 V, so one part number covers a bipolar instrumentation board and a 12 V industrial board. On plus or minus 5 V the analog range is plus or minus 5 V and the on resistance rises; the 1.5 ohm headline figure is the plus or minus 15 V number and should not be carried into a 5 V budget without checking the table.
Where it fits
Automatic test equipment, relay replacement in instrumentation, sample and hold front ends and any board that needs a four way selection with a resistance low enough to sit in series with a real load. For a channel that only sees a high impedance converter input, the ADG1204 does the same job with far lower charge injection.
Sourcing notes for this family: how to reduce component cost holds the cross references, one stop BOM sourcing is the pre substitution check, and defense grade components is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Is the ADG1404 a relay replacement? For a resistive load within 400 mA and within the supply rails, yes: it is faster, has no coil current and no wear. For an inductive load, or a load that can be disconnected while energised, a mechanical contact or a protected discrete switch is still the right answer.
What is the difference between the ADG1404 and the ADG1204? Both are 4 to 1 multiplexers in the same family and package. The ADG1404 has 1.5 ohm on resistance and a 400 mA current rating; the ADG1204 has 120 ohm and is built for picocoulomb charge injection on high impedance acquisition nodes. The choice is set by whether the path carries current or carries charge.