ADC0809CCN
Product Specifications
ADC0809CCN
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADC0809CCN from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADC0809CCN: 8-bit 8-channel successive approximation converter in a 28-pin DIP
The ADC0809CCN is the classic 8-bit converter with an eight channel multiplexer, a successive approximation register and microprocessor compatible control logic in a 28-pin DIP. It needs a single 5 V supply, converts in 100 us and dissipates 15 mW. The part is the through hole option for repairing and building instruments whose boards were laid out for the 0809 pinout, and it is still the cheapest way to put eight slow analog channels on a bus.
Published values
| Parameter | Value |
|---|---|
| Resolution | 8 bits |
| Channels | 8 single ended, with address latch and decoder |
| Conversion time | 100 us typical |
| Total unadjusted error | plus or minus 0.5 LSB and plus or minus 1 LSB depending on grade |
| Supply | single 5 V |
| Power dissipation | 15 mW |
| Input range | 0 V to VCC, ratiometric or with an adjusted reference |
| Outputs | latched three state, TTL levels |
| Clock | external, typically 640 kHz |
| Zero and full scale adjustment | not required |
| Package | 28-pin DIP |
100 us is 10 k samples per second
One conversion per channel takes 100 us, so a single channel runs at 10 k samples per second and eight channels scanned in sequence run at 1.25 k samples per second each. That is enough for a temperature logger, a slow strain gauge scanner or a panel meter, and it is two orders of magnitude away from an audio or vibration channel. Knowing the ceiling is what stops the part being specified into an application it cannot serve.
The eight bit resolution is 19.5 mV per code on a 5 V span, and the total unadjusted error of plus or minus 1 LSB means the part is specified to about 20 mV of absolute accuracy. A channel that needs 12 bits has to move to a different converter rather than average this one, because averaging removes noise and not quantisation.
The multiplexer and the sample and hold
The eight channel multiplexer has an address latch and a decoder, so a processor can write the channel number to the bus and start a conversion with two control lines. There is no internal sample and hold, which means the input has to stay stable for the whole 100 us conversion. A source with more than a few kiloohms of impedance therefore needs an external buffer or a capacitor at the pin, otherwise the conversion reads a moving target and the error looks like noise.
The converter can work rationmetrically, with the reference tied to the same 5 V rail as the sensor bridge, so the supply tolerance cancels. That is the configuration that made the part popular in weigh scales: a bridge and the converter on one rail gives a reading that does not move when the rail does.
Why a DIP part is still bought
The 28-pin DIP is solderable by hand, socketable, and removable. In test equipment and in instruments that are repaired rather than replaced, that is the difference between a board that goes back into service and a board that is scrapped. The same die in a surface mount body exists, but the through hole order code is what the service manual lists.
15 mW at 5 V is 3 mA, so the part does not need a heat path and can run from a linear regulator with no derating. A 640 kHz clock is the usual value and can come from a divider on the processor bus, which is why the part needs no crystal of its own.
When an order code in this family cannot be found, the ADC and DAC cross reference lists what else does the same job, the obsolete part cross reference hub covers what to check before a part is dropped into an existing board, and component obsolescence management is the route we take on a live shortage.
Two questions buyers ask
What replaces an ADC0809CCN when it is no longer available? The function is an 8-bit 8-channel converter with a parallel bus, so a replacement has to match the bus timing and not only the resolution. A pin compatible alternative from the same era is the practical route, and a modern converter in a different package needs a board revision and a new control sequence.
Does this part need an external clock? Yes, typically 640 kHz. There is no internal oscillator, so the clock has to come from the processor or from a divider, and the conversion time of 100 us assumes that clock.