Contact Us

ADA4891-2ARZ

Brand: Analog Devices
Analog Devices ADA4891-2ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADA4891-2ARZ — Analog & Mixed-Signal ICs | Superb Automation

ADA4891-2ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADA4891-2ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADA4891-2ARZ: dual 220 MHz CMOS video amplifier in an 8-lead SOIC

The ADA4891-2ARZ is the SOIC body of the dual member of the ADA4891 family: a CMOS rail to rail amplifier with a 240 MHz small signal bandwidth, a 170 V/us slew rate and 4.4 mA per amplifier. The MSOP version of the same die is a separate order code on this site. The SOIC is the one to take when the board is reflowed on an older line or when the channel has to survive repeated rework, and the electrical behaviour is the same.

Published values

ParameterValue
-3 dB small signal bandwidth240 MHz at a gain of 1, 90 MHz at a gain of 2 into 150 ohm
Slew rate170 V/us rising, 210 V/us falling
Settling time to 0.1 percent28 ns at a gain of 2, 2 V step
Supply current per amplifier4.4 mA
Offset voltageplus or minus 2.5 mV typical, plus or minus 10 mV maximum
Offset drift6 uV/C
Input bias current2 pA typical, plus or minus 50 pA maximum
Voltage noise9 nV per root hertz at 1 MHz
Supply range2.7 V to 5.5 V single supply
Output swingwithin 50 mV of either rail
Output current125 mA linear at 1 percent distortion
Input common modefrom 0.3 V below the negative rail to 0.8 V below the positive rail
Package8-lead SOIC_N

240 MHz is a gain of one number

At a gain of 2 into a 150 ohm load the bandwidth falls to 90 MHz, and the 0.1 dB flatness region is 25 MHz. A video driver built around this part therefore has a usable passband that is a quarter of the headline figure, which is normal for a voltage feedback amplifier and is the number that belongs in a link budget. The 28 ns settling time to 0.1 percent at a 2 V step is the switching figure: 28 ns is 35 MHz of equivalent single pole behaviour, so a multiplexer that has to settle between two sources is limited by settling rather than by bandwidth.

A 170 V/us slew rate at a 2 V peak to peak output gives 13.5 MHz of full power bandwidth, so a large signal channel and a small signal channel do not have the same ceiling. The two figures differ by a factor of seventeen, which is why the datasheet quotes both.

The input does not reach the positive rail

The input common mode range runs from 0.3 V below the negative rail to 0.8 V below the positive rail. On a 5 V supply that is a window from -0.3 V to 4.2 V, so a signal that swings to 5 V clips the input even though the output is rail to rail. A follower driven by a 0 to 5 V sensor therefore needs either a 0.8 V headroom in the signal or a divider, and this is the single most common mistake made with the part.

The bias current is 2 pA typical and 50 pA maximum, so a 1 Mohm source adds 50 uV at worst, which is small against the 2.5 mV typical offset. The offset, not the bias, is the dc error term here, and 10 mV maximum is 1.3 codes of a 12-bit converter on a 5 V span.

SOIC against MSOP on the same die

The two packages carry the same silicon, so the bandwidth, the noise and the offset are identical. What changes is the thermal path and the parasitics: the SOIC has a wider lead frame and a lower inductance path to the die, which matters when 125 mA of linear output current flows in a video cable driver, and the MSOP saves board area in a camera module where the amplifier is not the hot part.

Both are specified over -40 C to +125 C. A board that reflows the SOIC at a different profile from the MSOP should treat them as separate line items rather than as one part with two names, because the reflow profile and the stencil are decided by the package.

Buyers usually arrive at the amplifier cross reference to find the family alternatives, then use the ADC and DAC cross reference to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.

Two questions buyers ask

Can the ADA4891-2ARZ drive a 75 ohm video cable directly? Yes, it delivers 125 mA of linear output current and swings within 50 mV of the rails, so a 75 ohm doubly terminated load is inside its capability. The bandwidth at that load is the gain of 2 figure, 90 MHz, not the 240 MHz gain of 1 figure.

Is the SOIC version a different part number from the MSOP? Yes: the SOIC is ADA4891-2ARZ and the MSOP is ADA4891-2ARMZ. The die is the same and the electrical table is shared, but the order code, the footprint and the reflow profile are not interchangeable.