Contact Us

ADA4841-2YRMZ-R7

Brand: Analog Devices
Analog Devices ADA4841-2YRMZ-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADA4841-2YRMZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADA4841-2YRMZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADA4841-2YRMZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADA4841-2YRMZ-R7: 2.1 nV of noise on 1.1 mA, which is the pair a 16-bit front end needs

The ADA4841-2YRMZ-R7 is an Analog Devices dual operational amplifier with a rail to rail output, 1.1 mA of supply current per amplifier and 1.5 mA maximum quiescent, in an 8-lead MSOP. Voltage noise density is 2.1 nV per root hertz and current noise is 1.4 pA per root hertz, with 7 nV and 13 pA per root hertz at 10 Hz, so the 1/f corner is low. Distortion is minus 105 dBc at 100 kHz with a 2 V peak to peak output, the gain bandwidth is 80 MHz at unity gain, slew rate is 12 V per microsecond, settling to 0.1 percent is 175 ns, and offset voltage is 0.3 mV maximum. The output swings to within 50 mV of either rail, the input common mode range extends to the negative supply, and the supply range is 2.7 V to 12 V. It is on the analog and mixed-signal IC line card.

2.1 nV over a 100 kHz band is 664 nV, and that sets the converter resolution it can serve

Multiplying 2.1 nV by the square root of 100 kHz gives 664 nV rms, and over 1 MHz it gives 2.1 uV. A 16-bit converter on a 5 V span has a code of 76.3 uV, so the amplifier noise is 1 percent of a code in a 100 kHz band and 3 percent in a 1 MHz band. That is what allows the part to sit in front of a 16 or 18 bit converter without adding to the noise floor, and it is why the 1.1 mA supply current is remarkable: a 2 nV amplifier usually costs several milliamps.

ParameterVendor figureDerived figure
Supply current1.1 mA per amplifier11 mW per channel at 10 V, 22 mW for the package
Voltage noise2.1 nV per root hertz664 nV over 100 kHz, 2.1 uV over 1 MHz
Offset0.3 mV maximum3.9 LSB of a 16-bit converter on 5 V
Distortionminus 105 dBc at 100 kHz0.00056 percent, about 17 bits of spurious floor
Bandwidth80 MHz at unity gain8 MHz at a gain of 10, 800 kHz at a gain of 100
Slew rate12 V per microsecond1.9 MHz full power bandwidth at 2 V peak to peak
Output and loadwithin 50 mV of the rails, 10 pF directa series resistor is needed above 10 pF

The full power bandwidth is a quarter of what the gain bandwidth suggests

At 2 V peak to peak and 12 V per microsecond the largest undistorted sine is 1.9 MHz, while the small signal gain bandwidth is 80 MHz. The difference is the slew rate, and it is the number that matters for a converter driver at full scale. At a gain of 10 the closed loop bandwidth of 8 MHz is still above the slew limited figure, so the slew rate is the binding constraint, and a specification that quotes 80 MHz in a document is describing a 100 mV signal rather than a converter's full span.

Selection notes

  • Input common mode to the negative rail with a rail to rail output suits a single supply 5 V system with a ground referenced sensor.
  • 175 ns to 0.1 percent allows a successive approximation converter's acquisition window to close without a settling penalty at 1 MSPS.
  • Capacitive load above 10 pF needs a small series resistor, which is normal for an amplifier of this bandwidth and should be on the parts list rather than discovered on the bench.
  • Current noise of 1.4 pA per root hertz matters against a high impedance source, but at 100 kohm the resistor's own thermal noise of 40 nV dominates the amplifier.

Questions buyers ask

Can this drive an 18-bit converter? Yes in a narrow band. In a 100 kHz band its 664 nV is small against an 18-bit code of 19 uV, and in a 1 MHz band it is 2.1 uV, still a tenth of a code.

Is the dual version two independent amplifiers? Yes, and the second channel is often used as the reference buffer or the anti-alias stage in the same front end.

Converter drivers are compared on amplifier cross reference, and the matching converter families are on ADC DAC cross reference.

ADA4841-2YRMZ-R7: the twelve volt ceiling and the power down pin decide the socket

The supply range is 2.7 V to 12 V, so this amplifier fits a 10 V or a 12 V analog rail and does not fit the plus or minus 15 V rack that older instrumentation uses. At 12 V and 1.1 mA per amplifier the dissipation is 13.2 mW per channel, which is why the part appears in multi channel data acquisition cards where a rack amplifier would cook. The power down pin is the second half of the same idea: a channel that is not converting can be turned off and the 1.1 mA stops being a fixed cost.

ItemPublished valueArithmetic or consequence
Supply2.7 V to 12 VA plus or minus 15 V rack needs a different part
Supply current1.1 mA per amplifier, 1.5 mA maximum13.2 mW per channel at 12 V
Output swingWithin 50 mV of either railA 11.9 V span on a 12 V rail into a light load
Input rangeCommon mode extends to the negative supplyA ground referenced sensor works on a single rail
Settling175 ns to 0.1 percentNot the same as settling to 16 bit, which needs longer
Capacitive load10 pF before peakingA cable or a filter needs a series resistor at the output
Distortion-105 dBc at 100 kHz into 2 V peak to peakAbout 17 bits of spurious free range at that level

One hundred and seventy five nanoseconds is not sixteen bit settling

Settling to 0.1 percent is one part in a thousand, and 16 bits is one part in 65536, so a converter multiplexer that switches channels at 1 MSPS needs the amplifier to settle three orders of magnitude further than the headline number. The vendor positions the part for 16 and 18 bit converters, and the way to read that is a settling curve to 0.001 percent rather than the 175 ns figure. At 100 kSPS there is enough time, at 1 MSPS the curve decides.

Ten picofarads of load is a low number for a rail to rail output

An output that peaks with 10 pF is telling the user that any cable, any filter capacitor and any long trace needs a series resistor or a different amplifier. That is not a defect, it is the cost of the 80 MHz bandwidth at 1.1 mA, and it changes the bill of materials by one resistor per channel. A board that ignores it will show a 100 MHz oscillation on a scope and no error in a simulation.

Buying this order code

The YRMZ suffix is the 8-lead MSOP body with the power down pin, and the SOIC body is a different code. The precision amplifier family is on the analog line card, converter driver options are compared on the converter cross reference, and reels are booked through the lead time desk.

Request Quote — In Stock, 100% New & Original, Full Warranty