AD9838BCPZ-RL
Product Specifications
AD9838BCPZ-RL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD9838BCPZ-RL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD9838BCPZ-RL: 11 Milliwatts of Complete DDS in a 20 Lead Package
The AD9838BCPZ-RL is a complete direct digital synthesiser that draws 11 mW at 2.3 V, runs from 2.3 V to 5.5 V, accepts a master clock of 16 MHz in the B grade and produces sine, triangle and, through the on board comparator, square wave outputs up to 8 MHz. It has 28 bit frequency registers, which give 0.06 Hz resolution at a 16 MHz clock, and a 3 wire serial interface that runs to 40 MHz. Frequency and phase modulation are both available through the registers and through dedicated pins.
Eleven milliwatts over a year of battery life
Eleven milliwatts at 2.3 V is 4.8 mA, and 4.8 mA over a year is 41.9 Ah. That figure is what makes the part interesting for a battery instrument: the synthesiser is no longer the reason the product needs a larger cell, and the rest of the budget can go to the amplifier and the sensor. The same arithmetic explains why the DAC can be powered down when only the comparator output is used, since the sine output is the largest single consumer inside the die.
What the published figures convert to
| Parameter | Published figure | What it means on a board |
|---|---|---|
| Supply range | 2.3 V to 5.5 V | Runs from a lithium cell without a boost converter |
| Power at 2.3 V | 11 mW | 4.8 mA, which is 41.9 Ah over a year of continuous operation |
| Master clock | 16 MHz in the B grade, 5 MHz in the A grade | The grade is a real limit, not a binning label |
| Frequency resolution at 16 MHz | 0.06 Hz | 268 million steps across the range, so fine trim is digital |
| Frequency resolution at 5 MHz | 0.02 Hz | A lower clock gives finer steps but a lower output ceiling |
| Maximum output | 8 MHz | Half the master clock, so the reconstruction filter starts at 8 MHz |
| Outputs | Sine, triangle, square through a comparator | Three wave shapes from one part with no external switch |
| Serial interface | 3 wire, up to 40 MHz | Faster than the master clock, so a register update costs almost nothing |
| Modulation | Frequency and phase, by register or pin | A frequency shift keyed link needs no processor intervention |
| Supplies | Analog and digital independent | AVDD at 5 V with DVDD at 3 V keeps the analog output clean and the interface compatible |
| Power down | Per section through the SLEEP pin | The DAC can be off while the comparator drives a clock output |
| Package | 20 lead LFCSP | Fits beside a microcontroller on a small sensor board |
Checks before accepting a cross reference
- Compare the maximum master clock, not the typical. An A grade part at 16 MHz will not run.
- Check whether the comparator is included. Without it a square wave output needs an external comparator and a reference.
- Verify the frequency register width. A 24 bit part has 16 times coarser resolution at the same clock.
- Confirm the phase modulation path. Some DDS parts support frequency only, which rules out a phase modulated measurement.
- Ask about the reconstruction filter requirement, since the output is a sampled sine and the image at the clock frequency has to be removed.
Where this part is used
Frequency stimulus and waveform generation, impedance measurement, liquid and gas flow measurement, proximity and defect detection, test and medical equipment, and low power radio exciters. The common requirement is a precise, settable frequency with a supply current measured in milliamps.
Questions buyers ask
Can it generate a clock for a converter? Yes. The comparator converts the sine output to a square wave, and the DAC can be powered down once the clock is all that is needed.
How clean is the sine output? The on chip DAC is 10 bit, so the sine is quantised and requires a low pass filter. For a 10 bit class signal the part is adequate; for a signal generator front panel it is not.
Does the interface need a dedicated peripheral? No. The 3 wire interface is compatible with SPI, and a 40 MHz clock rate means a register write takes well under a microsecond.
Sourcing notes and next step
The synthesiser belongs to the RF and signal generation group on the analog and mixed signal index. Exciter chains that follow the synthesiser are covered in the RF component sourcing page, and the stage that turns the filtered output into a usable level is compared in the RF amplifier selection guide. Send the output frequency range, the required resolution and the supply rail and we will quote the correct clock grade and reel.
Request Quote — In Stock, 100% New & Original, Full Warranty