AD9680BCPZ-500
Product Specifications
AD9680BCPZ-500
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD9680BCPZ-500 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD9680BCPZ-500: The Headline Power Figure Belongs to the 1 GSPS Member of the Family
The AD9680 is a dual 14-bit converter family covering 500 MSPS, 820 MSPS, 1 GSPS and 1.25 GSPS with JESD204B serial outputs, a 2 GHz analogue input bandwidth and an internal digital down converter per channel. The BCPZ-500 code is the 500 MSPS member. The 1.65 W per channel printed on the front page is the figure at 1 GSPS with default settings, while the specification table gives 700 mW per channel for the 500 MSPS version, so a thermal budget written from the front page overstates the dissipation by more than a factor of two and, worse, a supply sized from it will look adequate when the real problem is elsewhere.
The serial link has to carry 14 bits at 500 MSPS twice
Two converters at 500 MSPS and 14 bits produce 14 Gb per second of payload. With 8b10b coding that is 17.5 Gb per second on the wire, and spread over four lanes it is 4.375 Gb per second per lane, which is inside the published 3.125 Gb to 12.5 Gb per lane range with room to spare. Spread over two lanes the same payload needs 8.75 Gb per second per lane, still legal. What is not legal is to run four lanes at the computed rate and then forget that the lane rate is set by the converter sample rate, so a later change from 500 MSPS to 820 MSPS moves every lane and can push the FPGA transceiver out of its own range.
| Item | Published value | What it decides |
|---|---|---|
| Resolution and rate | 14 bits at 500 MSPS | Payload rate and lane count |
| Power per channel | 700 mW at 500 MSPS | Thermal and supply sizing |
| SNR at 340 MHz | 65.3 dBFS at 1 GSPS | Noise floor against a full scale tone |
| SFDR at 340 MHz | 85 dBFS at 1 GSPS | Spurious limited dynamic range |
| ENOB | 10.8 bits at 10 MHz | Real resolution after noise and distortion |
| Input range | 1.46 V peak to peak to 2.06 V peak to peak | Front end gain and drive level |
| Full power bandwidth | 2 GHz usable | Direct IF sampling |
| Channel isolation | 95 dB | Crosstalk between the two converters |
Fourteen bits does not mean fourteen effective bits
The published ENOB of 10.8 bits at 10 MHz means the converter behaves like an 11-bit part in a real receiver, so a system noise budget built on 14 bits of headroom is 3.2 bits optimistic, which is a factor of nine in voltage. The noise density figure of minus 154 dBFS per hertz at 1 GSPS is the number that survives a decimation stage: narrow the band by a factor of ten and the noise floor drops by 10 dB, which is why the on chip down converter matters more than the raw sample rate in a narrowband receiver.
Clock, reference and the input network
The clock input is differential and the aperture jitter of the clock source adds directly to the SNR, so a 500 MSPS converter driven from a jittery clock will not reach its published SNR at high input frequencies. The internal reference removes one external part, and the programmable termination of 400, 200, 100 or 50 ohm allows a balun and a filter to be matched without extra resistors. The amplitude detect bits in the fast detect path give an AGC input without an external detector, which is the kind of integration that saves a whole RF section on a multi channel card.
Sourcing a converter that is on a JESD204B link
The substitution question for this part is the lane configuration and the firmware that programs it, not the analogue performance, because the interface is where a swap usually fails. The ADC DAC cross reference page covers the converter class, the medical device components page covers the imaging case, and the incoming inspection plan page covers lot verification.