Contact Us

AD8671ARZ

Brand: Analog Devices
Analog Devices AD8671ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8671ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8671ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8671ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8671ARZ: single precision low noise amplifier with 2.8 nanovolts of noise

The AD8671ARZ is the single channel member of the AD8671/AD8672/AD8674 family in an 8-lead SOIC_N body. It has 2.8 nV/root Hz of voltage noise, 10 MHz of gain bandwidth, a 75 uV maximum offset and 3 mA of supply current on plus or minus 5 V to plus or minus 15 V, which is the classic low noise precision front end for audio, instrumentation and converter drive.

Published values

ParameterValue
Offset voltage20 uV typical, 75 uV maximum
Input bias current-12 nA to +12 nA, 3 nA typical
Input offset current6 nA typical, 12 nA maximum
Supply current per amplifier3 mA typical, 3.5 mA maximum
Gain bandwidth10 MHz
Slew rate4 V/us
Settling time to 0.1 percent1.4 us on a 4 V step at unity gain, 2.2 us on a 10 V step
Voltage noise density2.8 nV/root Hz typical, 3.8 nV/root Hz maximum at 1 kHz
Noise, 0.1 Hz to 10 Hz77 nV p-p
Open loop gain1000 V/mV minimum, 6000 V/mV typical into 2 k
CMRR100 dB minimum at +-5 V, 120 dB at +-15 V
Input voltage range+-2.5 V on a +-5 V supply, +-12 V on a +-15 V supply
Output swing into 2 k+3.8 V minimum on a +-5 V supply, +13.2 V minimum on +-15 V
Supply range+-4 V to +-18 V

2.8 nanovolts against the resistor next to it

A 1 kOhm resistor at 300 K generates 4.07 nV/root Hz, so at that impedance the amplifier contributes less than the resistor it is connected to. At 10 kOhm the resistor is 12.9 nV and the amplifier is a quarter of the total. Below about 1.5 kOhm the 2.8 nV part is the right choice; above about 10 kOhm a 4 nV amplifier costs almost nothing in total noise and the choice should be made on offset and current.

The 77 nV p-p figure over 0.1 Hz to 10 Hz is the low frequency part, and it is consistent with the spot noise: 2.8 nV across 10 Hz is 8.9 nV rms, which at a 6.6 peak factor is 59 nV p-p. The measured 77 nV says there is a small 1/f contribution below 10 Hz, which matters to a slow channel and not to an audio one.

Bias current is the compromise

12 nA maximum of bias current is the price of a bipolar input with 2.8 nV of noise. Into a 100 kOhm source that is 1.2 mV, sixteen times the 75 uV offset, so a high impedance sensor is the wrong load for this part. Keep the source below about 10 kOhm and the bias error stays under 120 uV, which is the same order as the offset.

The offset current of 6 nA typical is what a difference stage sees: two bias currents that do not match produce an error across the source resistances, so a 10 kOhm pair gives 60 uV. Balance the two input resistances and the offset current term partly cancels, which is the old trick and still the cheapest one.

Headroom on plus or minus 5 V and plus or minus 15 V

The output reaches 3.8 V minimum into 2 k on a plus or minus 5 V supply and 13.2 V on plus or minus 15 V, so it is not a rail-to-rail part and loses about 1.2 V to 1.8 V at each end. A plus or minus 5 V system therefore has a usable span of about 7.6 V, and a 10 V converter range needs the plus or minus 15 V supply or a lower reference.

The input range is plus or minus 2.5 V on plus or minus 5 V and plus or minus 12 V on plus or minus 15 V, which is a similar amount of headroom. Both ends have to be checked against the signal, and on a plus or minus 15 V board a signal that goes to the rail is outside the part on both counts.

When an order code in this family cannot be found, how to verify a drop in replacement lists what else does the same job, the amplifier cross reference covers what to check before a part is dropped into an existing board, and one stop BOM sourcing is the route we take on a live shortage.

Two questions buyers ask

Is the AD8671ARZ rail to rail? No. The output stops 1.2 V short of each rail on a plus or minus 5 V supply, and the input range is plus or minus 2.5 V. It is a headroom part, not a rail-to-rail one.

What source impedance suits it? Below about 10 kOhm. At 1 kOhm the resistor noise already exceeds the amplifier noise, which is where a 2.8 nV part pays off.