AD8667ARZ
Product Specifications
AD8667ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8667ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8667ARZ: dual 16 volt precision CMOS amplifier at 250 microamps per channel
The AD8667ARZ is the two channel member of the AD8663/AD8667/AD8669 family in an 8-lead SOIC_N body. It puts a 175 uV maximum offset at 5 V, 300 fA of bias current and 23 nV/root Hz of noise on 275 uA maximum per amplifier, which is the combination for a high impedance measurement that has to run from a 12 V or 15 V rail without a milliamp budget.
Published values
| Parameter | Value |
|---|---|
| Offset voltage | 30 uV typical, 175 uV maximum at 5 V; 40 uV typical, 300 uV maximum at 16 V |
| Offset voltage drift | 1.5 uV/C typical, 5 uV/C maximum |
| Input bias current | 0.3 pA typical, specified in femtoamps |
| Input offset current | 0.2 pA typical |
| Supply current per amplifier | 210 uA typical, 275 uA maximum |
| Gain bandwidth | 520 kHz |
| Slew rate | 0.26 V/us |
| Voltage noise density | 23 nV/root Hz at 1 kHz |
| CMRR | 76 dB minimum at 5 V, 87 dB minimum at 16 V |
| Input voltage range | 0.2 V to 3.0 V at 5 V; 0.2 V to 14.5 V at 16 V |
| Output swing | 4.95 V minimum high at 100 uA, 4.65 V at 1 mA on a 5 V supply |
| Short circuit current | 7 mA |
| Phase margin | 60 degrees |
| Supply range | 5 V to 16 V single supply, +-2.5 V to +-8 V dual |
The offset moves with the supply
175 uV maximum at 5 V and 300 uV maximum at 16 V are not the same part in two columns: the input stage is trimmed by the DigiTrim process and the residual offset grows with the operating point. A 12 V system should read the 16 V column, not the 5 V one, and 300 uV is 3.9 codes of a 16-bit converter on 5 V or 1.2 codes on a 16 V span.
Drift of 5 uV/C maximum over 165 C is 825 uV, which is nearly three times the offset itself. That is the dominant error term on a hot board, and it is why this part suits a 12-bit or 14-bit channel that is calibrated in the enclosure rather than a 16-bit channel that has to hold its accuracy uncalibrated.
300 femtoamps and what it means at the input
300 fA of bias current into a 1 GOhm source is 0.3 uV, into 100 GOhm it is 30 uV, and into 1 TOhm it is 300 uV. So the part stays usable at a source impedance where a bipolar amplifier with 10 nA of bias current would be 10 mV out. That is the reason it appears on pH electrodes, photodiode transimpedance stages and electrometer style inputs.
At those impedances the board, not the amplifier, sets the leakage: a fingerprint, flux residue or a humid day is orders of magnitude worse than 300 fA. A guard ring driven at the input potential and a conformal coat do more for the measurement than any part change.
520 kHz on a 16 V rail
520 kHz of gain bandwidth at a gain of 100 is 5.2 kHz, and the 0.26 V/us slew rate means a 10 V step takes 38 us. A 12-bit channel sampled at 1 kSPS gives each sample 1 ms, so the amplifier settles within it; a channel at 100 kSPS does not. The output swing of 4.65 V minimum at 1 mA on a 5 V supply also matters: 3.5 mV of headroom is lost per code, and a converter with a 4.096 V reference is a better match than one with a 5 V reference.
The 7 mA short circuit current is small because the output stage is small, which is the price of 275 uA of quiescent current. Driving a cable or a low impedance load from this part is outside what it was made for; a buffer after it is the correct answer.
Where a customer needs a second position on this part, medical device components is the starting point, the amplifier cross reference sets out the checks a substitution has to pass, and component lead time solutions is the short lead time route we quote against.
Two questions buyers ask
Why is the offset different at 5 V and 16 V? Because the input stage trimming is specified at each supply. Use the 16 V figure, 300 uV maximum, on any board that runs above 5 V.
Is this the same amplifier as the AD8666? No. Both are 16 V CMOS duals, but the AD8666 is a 4 MHz part with a 2.5 mV offset on 1.4 mA, and the AD8667 is a 520 kHz part with a 175 uV offset on 275 uA. The sockets are compatible in the 8-lead SOIC, the behaviour is not.