AD8629ARMZ-REEL
Product Specifications
AD8629ARMZ-REEL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8629ARMZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8629ARMZ-REEL: zero drift with a 1 microvolt offset, in an eight lead MSOP
The AD8629 is the dual member of the AD8628, AD8629 and AD8630 zero drift family, an auto zero amplifier with rail to rail input and output specified from 2.7 V to 5 V single supply. The order code reads RM for the eight lead MSOP body, Z for RoHS and REEL for the 13 inch reel, so this is the small package rather than the narrow SOIC. The vendor page gives the offset as 1 microvolt, the drift as 0.002 microvolts per degree C, the input bias current as 100 pA maximum and the supply current as 1.0 mA for the dual. The point of a zero drift part is not the initial offset but the fact that the offset stays where it is over temperature and time, which is what a strain gauge or a thermocouple channel needs.
What the vendor page states
| Parameter | Value |
|---|---|
| Channels | two, in an eight lead MSOP or narrow SOIC |
| Offset voltage | 1 microvolt |
| Offset drift | 0.002 microvolts per degree C, under 0.005 quoted in the overview |
| Supply | 2.7 V to 5 V single, plus or minus 1.35 V to plus or minus 2.5 V dual |
| Input and output swing | rail to rail on both |
| Gain, CMRR, PSRR | 130 dB |
| Input bias current | 100 pA maximum |
| Supply current | 1.0 mA for the dual |
| Low frequency noise | 0.5 microvolts peak to peak, 0.1 Hz to 10 Hz |
| Overload recovery | 50 microseconds |
| External components | none required |
What 0.002 microvolts per degree C means over the full range
Across the 165 degree span from minus 40 C to plus 125 C the drift term comes to 0.33 microvolts, which is a third of the 1 microvolt initial offset. That is the whole argument for the part: a conventional precision amplifier with 1 microvolt per degree C of drift would move 165 microvolts over the same span, and no factory trim survives that. The other half of the argument is that the drift does not need a chopper capacitor or a second gain stage, so the channel keeps its 130 dB of common mode rejection without a matching network.
The bias current is 100 pA, and that sets the source resistance it can see
At 100 pA a 1 megohm source develops 100 microvolts, which is a hundred times the initial offset and the same order as the drift. The vendor's own application list, pressure and position sensors, strain gauges, thermocouples and photodiodes, all sit in that range, and the honest reading is that above 1 megohm the bias current, not the offset, is the error source to plan around. Below 100 kilohm the bias term falls to 10 microvolts and the 1 microvolt offset dominates, which is where the part looks best on paper.
The noise floor of an auto zero stage
The 0.5 microvolts peak to peak figure over 0.1 Hz to 10 Hz converts to 76 nanovolts rms, or about 24 nV per root hertz across that band. For a dc channel that is the number that matters, because the band is where the sensor signal lives. The vendor page also claims the lowest noise among auto zero amplifiers and states that the family greatly reduces the digital switching noise found in most chopper stabilised parts, which is the usual objection to this class: the switching artefacts land at a frequency where a slow channel cannot filter them out.
Overload recovery and the 50 microsecond figure
When an auto zero amplifier is driven into saturation, the internal loop has to recover before the output is valid again. The page quotes 50 microseconds, which is what a multiplexed channel needs if the previous channel had a much larger signal. In a scanner that switches between a 10 mV thermocouple and a 5 V supply rail, that recovery time sets the minimum settling window per channel, and 50 microseconds is fast enough that the converter, not the amplifier, becomes the limit.
Where the dual lands
Two zero drift channels in an MSOP cover the common bridge configuration where both halves of a differential pair have to track, and the 1.0 mA total is 2.5 mW per amplifier on a 5 V rail, which is low enough for a battery powered instrument. The amplifier cross reference lists the single and quad members of the same family, the obsolete part hub tracks life cycle status on the earlier chopper parts this one replaces, and the analog and mixed signal category page holds the rest of the precision family.
Request Quote — In Stock, 100% New & Original, Full Warranty