AD8572ARZ
Product Specifications
AD8572ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8572ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8572ARZ: dual zero-drift amplifier, 5 microvolts offset and 145 dB gain
The AD8572ARZ is a two channel zero-drift amplifier in an 8-lead SOIC_N specified over -40 to +125 C with a 5 uV maximum offset, 0.04 uV/C maximum drift, rail-to-rail input and output, and 145 dB of typical open loop gain at 850 uA per amplifier. It suits a high gain DC channel where the loop needs open loop gain to hold the closed loop accuracy, not just a small offset at the input.
Published values
| Parameter | Value |
|---|---|
| Offset voltage | 1 uV typical, 5 uV maximum per amplifier |
| Offset voltage drift | 0.005 uV/C typical, 0.04 uV/C maximum |
| Input bias current | 10 pA typical, 50 pA maximum |
| Open loop gain | 125 dB minimum, 145 dB typical |
| Supply current per amplifier | 850 uA typical, 975 uA maximum at 5 V |
| Gain bandwidth | 1.5 MHz at 5 V, 1 MHz at 2.7 V |
| Slew rate | 0.4 V/us at 5 V |
| Voltage noise density | 51 nV/root Hz at 1 kHz |
| Noise, 0.1 Hz to 10 Hz | 1.3 uV p-p |
| CMRR and PSRR | 120 dB minimum each |
| Overload recovery | 0.05 ms typical, 0.3 ms maximum |
| Supply range | 2.7 V to 5.5 V single supply |
Open loop gain sets the closed loop error at high gain
At a closed loop gain of 1000 the finite open loop gain is the dominant error, not the offset: 125 dB is a factor of 1.8 million, so a gain of 1000 loses 0.06 percent, and the same calculation at 100 dB would lose 0.9 percent. That is the reason the gain line is on this page at all. An instrumentation amplifier built from two of these channels plus a difference stage keeps its gain error inside a few hundredths of a percent without trimming, which a 100 dB part cannot do.
Noise against the AD8552, where the sheets differ
The AD8572 lists 51 nV/root Hz and 1.3 uV p-p at low frequency, while the AD8552 lists 42 nV/root Hz and 1.0 uV p-p for the same 850 uA per amplifier. Everything else on the two sheets is close enough to be interchangeable, so if the noise floor of a low level channel is the deciding term, the AD8552 is the better of the two and the AD8572 is the part to keep when the gain figure and the second source position matter more.
Single supply, rail-to-rail, and what that does to a bridge
A four wire bridge sitting at half the excitation needs an amplifier whose input reaches both rails and whose output can drive a converter that also runs rail to rail. This part does both, so the bridge, the amplifier and the converter can share one 3.3 V rail with no charge pump. The price is that the input stage is a switched capacitor structure and the input current, 50 pA maximum, is a leakage term rather than a bias term, so it does not reverse sign with the common mode voltage the way a bipolar input does.
Commissioning notes
Zero drift parts are sensitive to the source impedance seen at each input, so match the two source resistances within a few percent. A 1 kOhm mismatch with 50 pA of bias current is 50 nV, which is below the noise floor, while a 1 MOhm mismatch is 50 uV and ten times the offset the part was chosen for.
For a board that has to keep running while a reel runs out, the amplifier cross reference is where the family alternatives sit, the ADI second source page is the check list before a substitute goes in, and medical device components is how a gap is covered without a new line item.
Two questions buyers ask
Is the AD8572ARZ specified over the automotive temperature range? The part is specified from -40 to +125 C, which covers the range, but the automotive grade order codes should be confirmed on the ordering guide before a production release.
How long does it take to recover from an overload? 0.05 ms typical and 0.3 ms maximum, which is the figure to use when a sensor can saturate the input during power up or a fault.