AD8544ARZ
Product Specifications
AD8544ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8544ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8544ARZ: four 45 microamp rail-to-rail amplifiers in a 14-lead SOIC
The AD8544ARZ is the quad member of the AD8541/AD8542/AD8544 CMOS family in a 14-lead narrow SOIC, giving four independent rail-to-rail channels at 45 uA each with 1 MHz of bandwidth and a 6 mV maximum offset. It is the part that buffers four sensor channels or four ADC inputs from one rail while the whole bank costs less than 0.3 mA.
Published values
| Parameter | Value |
|---|---|
| Offset voltage | 1 mV typical, 6 mV maximum per amplifier |
| Offset voltage drift | 4 uV/C typical |
| Input bias current | 4 pA typical, 60 pA maximum |
| Supply current, four channels | 180 uA typical, 260 uA maximum at 5 V |
| Gain bandwidth | 1 MHz at 5 V supply |
| Slew rate | 0.45 V/us typical, 0.92 V/us at 5 V |
| Voltage noise density | 42 nV/root Hz at 1 kHz |
| Output swing at 1 mA | 4.9 V minimum high, 25 mV typical low at 5 V supply |
| Package options | 14-lead narrow SOIC and 14-lead TSSOP |
| Phase margin | 67 degrees |
| Supply range | 2.7 V to 5.5 V single supply |
| Channel to channel offset | independent, no matching published |
The current bank, not the amplifier, is the specification
Four channels at 65 uA maximum is 260 uA from the rail, and that is the number to put in the power budget rather than the 45 uA headline. On a 3.3 V rail the bank costs 0.86 mW, which is still less than one 16-bit delta-sigma converter, so the quad is usually the right answer when four low frequency channels share a board.
Crosstalk through a shared package
Four amplifiers on one die share the positive and negative rails. When one channel drives a switched capacitive load, the current pulse travels out of the shared supply pin and back into the other three channels. At these bandwidths the disturbance is a few tens of microvolts and it decays within a microsecond, which is invisible to a DC measurement and visible on a 12-bit channel sampling at the same instant. Sequence the sampling so that a channel is not converted while another is slewing, or decouple each supply pin separately if the package allows it.
Where a quad of this class earns its place
Threshold detection on four rails, four channel 10-bit monitoring, four first order low pass sections ahead of a multiplexer, and buffering four reference taps are all sockets where 6 mV of offset is irrelevant and four channels in one body saves both board area and assembly cost. A four channel instrumentation front end is not one of them: the offset and its 4 uV/C drift dominate there, and four auto-zero parts are the honest answer.
The offset does not track between channels
Nothing in the datasheet promises matched offsets between the four amplifiers, so a ratiometric measurement that assumes channel A and channel B drift together is not supported. Each channel carries its own 6 mV maximum and its own untrimmed 4 uV/C typical drift, and the difference between two channels can be twice either figure.
Where a customer needs a second position on this part, one stop BOM sourcing is the starting point, the amplifier cross reference sets out the checks a substitution has to pass, and vendor consolidation is the short lead time route we quote against.
Two questions buyers ask
Can four spare channels be paralleled for lower noise? Not usefully on this part. Paralleling four voltage amplifiers lowers the noise by a factor of two at best, and the 42 nV/root Hz floor is set by the input stage rather than the output, so a single 8 nV part is a better answer than four of these.
Is the 14-lead TSSOP version electrically identical? Yes, the same die in a different body. Only the thermal path and the footprint change, so a board can move between the two packages without touching the circuit.