Contact Us

AD8539ARZ

Brand: Analog Devices
Analog Devices AD8539ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8539ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8539ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8539ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8539ARZ: dual auto-zero amplifier with a 15 microvolt maximum offset

The AD8539ARZ is the two channel member of the AD8538/AD8539 auto-zero family in an 8-lead SOIC_N body. Each amplifier holds a 15 uV maximum offset at 25 C and 0.1 uV/C maximum drift across the whole -40 to +125 C range while drawing 180 uA per amplifier, so a bridge or thermocouple front end can be built without a trimpot, a factory calibration step or a periodic re-zero in the field.

Published values

ParameterValue
Offset voltage, 25 C5 uV typical, 15 uV maximum per amplifier
Offset voltage, -40 to +125 C30 uV maximum
Offset voltage drift0.03 uV/C typical, 0.1 uV/C maximum
Input bias current15 pA typical, 60 pA maximum, 1 nA maximum at 125 C
Supply current per amplifier170 uA typical, 210 uA maximum at 5 V
Gain bandwidth430 kHz
Slew rate0.4 V/us at 5 V supply
Voltage noise density52 nV/root Hz at 1 kHz
Noise, 0.1 Hz to 10 Hz1.2 uV p-p
CMRR and PSRR115 dB and 105 dB minimum
Settling to 0.01%10 us on a 2 V step at unity gain
Supply range2.7 V to 5.5 V single supply

Which offset figure applies to a real instrument

The 15 uV line is a 25 C number measured at mid supply with the input at 2.5 V. The line that decides an instrument specification is the 30 uV maximum over -40 to +125 C, because a sealed enclosure with a regulator inside runs well above room temperature. The two lines are consistent: 15 uV at 25 C plus 0.1 uV/C over a 100 C excursion gives 25 uV, and the sheet allows 30 uV.

Two channels share a die and a correction loop clock, so the two offsets track each other. A differential measurement that subtracts channel A from channel B therefore cancels most of the residual, which is why this part appears in bridge front ends more often than its single channel version.

Where 430 kHz stops being enough

430 kHz of gain bandwidth is plenty for a DC channel and short for anything that scans. In a closed loop gain of 100 the bandwidth is around 4 kHz, and a 2 V step at 0.4 V/us takes 5 us before the loop has even started to settle, which is why the settling line reads 10 us. A 16 channel scanner running at 1 kSPS per channel gives each channel 1 ms, so the amplifier is not the limit. Run the same part at 100 kSPS and the settling tail is the limit, and a 1 MHz class part is the cheaper answer than a faster converter.

The noise floor is white, not 1/f

An auto-zero part is sometimes suspected of carrying extra low frequency noise from its correction loop. The numbers here say otherwise. Integrating 52 nV/root Hz across 10 Hz gives about 164 nV rms, and at the usual 6.6 peak factor that is 1.1 uV p-p, against a published 0.1 Hz to 10 Hz figure of 1.2 uV p-p. The two agree, so the low frequency line is the same white floor measured over a narrow band, and there is no 1/f rise to budget for.

Current and headroom

Two amplifiers at 210 uA maximum are 420 uA from the rail. On a 3.3 V rail that is 1.4 mW for the pair, which is small next to a 12-bit converter but not next to a 24-bit one that draws 300 uA in total. Check the total before choosing a part for a two wire transmitter, where the whole loop has 4 mA and the electronics must fit inside 3.5 mA.

For a board that has to keep running while a reel runs out, the amplifier cross reference is where the family alternatives sit, how to verify a drop in replacement is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.

Two questions buyers ask

Is the AD8539ARZ a straight swap for the AD8552ARZ? The package and the pinout are the same 8-lead SOIC_N dual, but the electrical behaviour is not: 170 uA and 430 kHz here against 850 uA and 1.5 MHz on the AD8552. The socket fits, the loop does not behave the same, so the compensation and the settling budget have to be checked on the board.

What happens to the input at 125 C? Bias current rises from 60 pA maximum to 1 nA maximum. Into a 1 MOhm source resistor that is 1 mV of error, which is larger than the offset the part was chosen for, so keep the source impedance low or buffer it.