Contact Us

AD8534ARZ

Brand: Analog Devices
Analog Devices AD8534ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8534ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8534ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8534ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8534ARZ: four rail-to-rail amplifiers that each drive 250 milliamps

The AD8534ARZ is the quad member of a single supply family whose selling point is output current rather than precision. Each amplifier drives plus or minus 250 mA, runs from 2.7 V to 6 V, draws 750 microamps and has 3 MHz of bandwidth. Input offset is 25 mV maximum, CMRR is 38 dB minimum, and the output impedance at 1 MHz is 60 ohms. It is built for headphones, LCD bias, small motors and capacitive loads, where 250 mA and no phase reversal matter more than microvolts.

Published values

ParameterValue
Supply range2.7 V to 6 V single supply
Output currentplus or minus 250 mA per amplifier
Supply current750 microamps per amplifier typical, 1 mA maximum, 1.25 over temperature
Bandwidth3 MHz at unity gain, 2.2 MHz gain bandwidth product
Slew rate3.5 V per microsecond
Settling1.6 microseconds to 0.01 percent
Input offset25 mV maximum, 30 mV over -40 to +85
Offset drift20 microvolts per degree
Input bias current5 pA typical, 50 pA maximum
CMRR38 dB minimum, 45 typical
Output swing2.92 V high and 100 mV low at 10 mA on a 3 V supply
Output impedance60 ohms at 1 MHz at unity gain
Phase margin70 degrees
Other featuresrail-to-rail input and output, no phase reversal, unity gain stable
Package14-lead SOIC, quad

Twenty five millivolts of offset, stated without apology

A part with 25 mV of input offset is not an instrumentation amplifier and should not be bought as one. What it is, is a driver: a headphone amplifier, an LCD common voltage buffer, a small solenoid or an LED string, where the load current and the freedom from phase reversal are the requirements and the dc accuracy is provided by the signal before it arrives.

Twenty five millivolts on a 1 V signal is 2.5 percent, and on a 100 mV signal it is 25 percent. Any circuit that needs better has to trim, or use a different part. The 20 microvolts per degree of drift then adds 1.2 mV over 60 degrees, which is small next to the room temperature offset.

Two hundred and fifty milliamps from a 3 volt rail

250 mA into a 10 ohm load at 3 V would need 2.5 V across the load, which the part can nearly do, but it dissipates 0.5 W in the package while doing it. A 14-lead SOIC in still air is about 100 degrees per watt, so the die would rise 50 degrees above ambient and the thermal shutdown would follow shortly.

The datasheet's own output numbers are taken at 10 mA, where the swing is 2.92 V and the dissipation is 8 mW. The 250 mA figure is a peak current capability for pulses and for loads that only occasionally demand it, not a continuous operating point. A board that draws 250 mA continuously from all four amplifiers is a 1 A load and belongs on a different device.

No phase reversal and 60 ohms of output impedance

No phase reversal means an input driven beyond the common mode range does not invert the output, which in a control loop prevents the latch up that turns a small overload into a dead channel. On a part with a rail-to-rail input this matters, because the input stage changes structure near the rails and many amplifiers do invert there.

The 60 ohm output impedance at 1 MHz is the reason the part drives capacitive loads well: a 100 nF load with 60 ohms forms a 26 kHz pole, which is inside the loop and stable, where a lower impedance output would push the pole out and ring. Phase margin of 70 degrees at unity gain is the other half of that stability story.

For a board that has to keep running while a reel runs out, the amplifier cross reference is where the family alternatives sit, one stop BOM sourcing is the check list before a substitute goes in, and the pin to pin cross reference is how a gap is covered without a new line item.

Two questions buyers ask about the high current quad

Can it run from a 5 V supply with a 5 V logic signal on the input? Yes, the input is rail-to-rail and the supply range covers 5 V. The absolute maximum on the supply is 6 V, so a 5 V rail at plus 10 percent is at the edge and needs checking.

Is the 250 mA output per amplifier or for the package? Per amplifier, and the package dissipation is what limits it. Four channels at 250 mA at the same time would be 1 A and well past the thermal capability of the 14-lead body.