AD8397ARDZ-REEL7
Product Specifications
AD8397ARDZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8397ARDZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8397ARDZ-REEL7: 310 mA into 32 ohms and 3.2 W to get rid of
The AD8397 is a dual voltage feedback amplifier with a rail-to-rail output stage that can deliver 310 mA peak into a 32 ohm load on plus and minus 12 V supplies while holding minus 80 dBc of spurious free dynamic range. It works from 3 V to 24 V total supply, swings to within 0.5 V of each rail into a 25 ohm load, has 69 MHz of bandwidth at unity gain and a 53 volt per microsecond slew rate. The output stage is a common emitter rather than an emitter follower, which is how it reaches a heavy load with a large swing. The ARDZ suffix is the 8-lead SOIC, and the vendor also offers a thermally enhanced 8-lead SOIC with an exposed pad for higher dissipation.
What the vendor page states
| Parameter | Value |
|---|---|
| Channels | two, voltage feedback |
| Supply range | 3 V to 24 V |
| Output swing | within 0.5 V of either rail into 25 ohms |
| Linear output current | 310 mA peak into 32 ohms on plus and minus 12 V at minus 80 dBc |
| Voltage noise | 4.5 nanovolts per root hertz at 100 kHz |
| Current noise | 1.5 picoamps per root hertz at 100 kHz |
| Bandwidth | 69 MHz at unity gain |
| Slew rate | 53 volts per microsecond into 25 ohms |
| Temperature | minus 40 C to plus 85 C |
| Package | 8-lead SOIC, also 8-lead SOIC with exposed pad |
What 310 mA means in watts
A 310 mA peak into 32 ohms is 9.92 V peak, which is 7.01 V rms and 1.54 W delivered to the load. Driving a sine that large from plus and minus 12 V draws an average of 197 mA from the 24 V total supply, which is 4.74 W in, so 3.2 W stays in the package as heat. That is the number that decides the package: an 8-lead SOIC without a thermal pad cannot pass 3.2 W to a board without a large copper area and airflow, and the exposed pad version exists precisely because of this arithmetic. Any application that quotes 310 mA has to state the load, the supply and the duty cycle, or it is quoting a transient rather than an operating point.
The 85 C ceiling follows from the dissipation
The specified temperature range stops at 85 C, while most industrial amplifiers on the same catalogue page reach 125 C. The reason is the same 3.2 W: the die is already hot from its own output stage, and a 125 C ambient would leave no junction headroom at all. A line driver in a sealed box has to be derated from the 85 C figure, not from a hopeful 125 C one, and a board that runs the part at 200 mA continuous should treat the thermal path as the first item on the thermal review rather than the last.
Noise, bandwidth and the 47 microvolts across the band
A 4.5 nanovolt density across a 69 MHz bandwidth is 46.8 microvolts rms, which sets the noise floor of anything this part drives. That is fine for a twisted pair line driver and too much for a low level sensor, which is the trade the part makes: it is built for current and swing, not for quietness. The current noise of 1.5 pA per root hertz becomes 4.74 microvolts across a 10 kohm source in a 100 kHz band, so a high impedance feedback network turns the current noise into the dominant term. The slew rate of 53 volts per microsecond puts a full 20 V peak to peak swing at 844 kHz, so the 69 MHz bandwidth is only available at small signal.
For the line driver and audio members of this family the amplifier cross reference lists the shared SOIC footprints, the component lead time page covers what to do when the exposed pad version is on allocation, and the analog and mixed signal category page holds the rest of the high current amplifier range.
Request Quote — In Stock, 100% New & Original, Full Warranty