AD829JRZ
Product Specifications
AD829JRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD829JRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD829JRZ: 120 MHz With 1.7 nV of Noise and External Compensation
The AD829JRZ is a video amplifier whose specification sheet reads like a low noise instrumentation part. Input voltage noise is 1.7 nV per root hertz, current noise is 1.5 pA per root hertz, and the maximum input offset is 1 mV over temperature, which is unusual for a device with 120 MHz of bandwidth at a gain of minus one. The bandwidth is not fixed by an internal capacitor: the part is compensated externally, so the same device can be set for gains from 1 to 20 by choosing the compensation components, trading bandwidth for stability at each gain. Supply current is 5 mA and differential gain is 0.02 percent, which is what puts it in broadcast quality signal paths.
Published values
| Parameter | Value |
|---|---|
| Bandwidth | 120 MHz at a gain of minus one |
| Input voltage noise | 1.7 nV per root hertz |
| Input current noise | 1.5 pA per root hertz |
| Input offset voltage | 1 mV maximum over temperature |
| Compensation | External, gains 1 to 20 |
| Supply current | 5 mA |
| Differential gain | 0.02 percent |
| Offset null | Dedicated pins |
| Body | 8-lead small outline and DIP forms, plus a 16-lead body |
Why external compensation is a feature rather than a nuisance
An internally compensated amplifier is stable at unity gain, which means it is slower than it needs to be at every gain above one. The AD829 leaves the compensation network to the user, so a stage running at a gain of ten can be compensated for that gain and keep far more bandwidth than an internally compensated part would deliver. The cost is that the board must carry the compensation components, and a substitution to an internally compensated amplifier changes the loop and usually the response. On a mature board the compensation network is part of the circuit, so the part number has to match the network it was tuned for.
Noise arithmetic in a low level video path
At 1.7 nV per root hertz the voltage noise is low enough that a 1 kohm source resistance contributes more noise than the amplifier, which is the crossover point that matters when a sensor or a cable termination sets the impedance. The current noise of 1.5 pA per root hertz then becomes significant only above a few tens of kilohms of source impedance, so the part suits low and moderate impedance stages and is the wrong choice for a high impedance photodiode front end. Reading the two noise figures together against the source impedance is the only way to predict the noise of the finished channel.
Offset null pins and the drift question
The package brings out offset null pins, and the data sheet notes that the 1 mV maximum offset applies over temperature rather than at room temperature alone. That distinction matters in a DC coupled video stage, where a null set at 25 degrees does not hold across the operating range unless the drift is low. Trimming with the null pins is worth doing only when the residual after trim is smaller than the drift over temperature, otherwise the trim is cosmetic. In an AC coupled stage the offset is removed by the coupling network and the null pins are best left unconnected.
Finding a compensation matched replacement
Because the part is externally compensated, an equivalent replacement has to match the compensation pin arrangement and the gain bandwidth product at the gain the stage actually runs. Two parts with the same headline bandwidth but different internal compensation will not produce the same response in the same socket. The practical approach is to keep the body and the pinout, compare the compensation scheme, and check the closed loop response on the real board rather than on a model. The amplifier cross reference page lists the externally compensated video parts we hold, the pin to pin cross reference page shows which bodies are direct swaps, and the lead time page covers availability for a build that is already in test.