Contact Us

AD8227ARMZ-R7

Brand: Analog Devices
Analog Devices AD8227ARMZ-R7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8227ARMZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

AD8227ARMZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8227ARMZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8227ARMZ-R7: Gain of Five and Up, 350 Microamps, Wide Supply

The AD8227ARMZ-R7 is a wide supply instrumentation amplifier whose gain starts at five rather than one: gain is 5 plus 80 kohm divided by RG, so with no resistor the part is a gain of five and with a resistor it reaches 1000. It runs from 2.2 V to 36 V single supply or plus and minus 1.5 V to 18 V dual, draws 350 microamps typical, has 250 kHz of bandwidth at a gain of five, 100 dB minimum common-mode rejection in the B grade at that gain, 24 nV per root hertz of input noise, and an output that swings to within 0.2 V of either rail. Specified temperature is minus 40 to plus 125 degrees Celsius, which with an 8-lead MSOP body makes it a fit for packed boards with no airflow.

Published values

ParameterValue
Gain5 to 1000, G = 5 + 80 kohm divided by RG
Supply, single2.2 V to 36 V
Supply, dualplus and minus 1.5 V to 18 V
Supply current350 microamps typical
Bandwidth250 kHz at gain of 5
Common-mode rejection100 dB minimum at gain of 5, B grade
Input noise24 nV per root hertz
Output swingWithin 0.2 V of either rail
Settling35 microseconds to 0.01 percent at gains of 5 to 100
Input rangeBelow ground, protected beyond the supplies
Temperatureminus 40 to plus 125 degrees Celsius
Package8-lead MSOP

A floor of five in the gain equation is a filter decision

Starting at a gain of five means the part cannot be used as a unity gain buffer, and that is deliberate: it is aimed at small signals that always need at least a factor of five. For a thermocouple with a 40 microvolt per degree output and a 5 V full scale, a gain of about 100 is needed, so the floor never binds. For a 4 to 20 mA receiver across a 100 ohm resistor, 2 V of signal, the gain is set below five and this is the wrong part. Checking that the required gain is above five before choosing is faster than reading the rest of the table, and it avoids the common mistake of fitting a resistor below the internal value and getting a gain that the equation does not predict.

Output to within 0.2 V of the rails, measured at the load

At 3 V and a gain of 100 the output can reach 2.8 V, leaving 200 mV of headroom to the positive rail and the same to the negative. On a 12-bit converter with a 3 V reference that is 273 codes lost at the top and bottom, which matters if the sensor's full scale is near the rail. The swing specification is at a light load; into 2 kohm the numbers hold, into 600 ohm they do not. For a board that drives a converter directly, 2 kohm is a comfortable load and the specification applies without derating.

Packed boards and the 125 degree specification

The part is specified to 125 degrees ambient, not just operational, which is the useful distinction: at that temperature the offset drift over the full range is bounded by the datasheet rather than by inference. In a sealed enclosure with no airflow the local ambient can exceed the outside temperature by 15 to 20 degrees, so a 105 degree internal measurement already means the amplifier is at its limit. Its 350 microamps draw 3 mW at 9 V, so the part itself is not the heat source; the regulators and the power stage are. Position it away from them and the drift specification holds.

Settling and the multiplexed front end

Settling to 0.01 percent takes 35 microseconds at gains of 5 to 100, which sets the maximum scan rate for a multiplexed front end: 28 kSPS per channel with no allowance for the multiplexer and the source. In practice a 1 kSPS to 5 kSPS scan is what the surrounding circuit allows, and the settling time is not the limit. What is often missed is the settling after a gain change, if the gain is switched with a multiplexer in the RG path: the internal nodes have to recharge through the new resistor, and that takes longer than the specified settling. Switch the gain only between scans, never within one.

Availability and second sourcing

A gain that starts at five makes substitution awkward: a part with a gain equation starting at one will not produce the same output for the same resistor. The parameters to compare are the gain equation, the common-mode range and the output swing to the rails. The amplifier cross reference page lists the wide supply family with its gain equations, the pin to pin cross reference page covers the 8-lead outlines, and the lead time page shows what is available.