AD8226ARMZ
Product Specifications
AD8226ARMZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8226ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8226ARMZ: Wide Supply Range Instrumentation Amplifier, MSOP
The AD8226ARMZ is a low cost instrumentation amplifier that runs from 2.2 V to 36 V single supply or plus and minus 1.35 V to 18 V dual, with gain set from 1 to 1000 by one resistor through 1 plus 49.4 kohm divided by RG. It draws 350 microamps typical, has 1.5 MHz of bandwidth at unity gain, 90 dB minimum common-mode rejection in the BR grade at unity gain, and 22 nV per root hertz of input noise. The input works below ground and is protected beyond the supplies: on a 5 V rail the part survives 35 V at the input without damage, which is the specification that makes it usable on industrial front ends where a miswire is expected.
Published values
| Parameter | Value |
|---|---|
| Gain | 1 to 1000, G = 1 + 49.4 kohm divided by RG |
| Supply, single | 2.2 V to 36 V |
| Supply, dual | plus and minus 1.35 V to 18 V |
| Supply current | 350 microamps typical |
| Bandwidth | 1.5 MHz at gain of 1 |
| Common-mode rejection | 90 dB minimum at gain of 1, BR grade |
| Input noise | 22 nV per root hertz |
| Input range | Goes below ground, protected beyond the supplies |
| Input survival | 35 V at the input on a 5 V supply |
| Output swing | Within 1.2 V of the negative rail, 1.1 V of the positive |
| Temperature | minus 40 to plus 125 degrees Celsius |
| Package | 8-lead MSOP |
Thirty-five volts at the input on a five volt supply
Industrial front ends see miswiring, and a 24 V loop accidentally connected to a 5 V input is the standard failure. The part specifies survival at 35 V at the input with a 5 V supply, so the amplifier is not the component that fails; the series resistor and the protection diode still have to be sized, because the survival rating is at the pin and the current through the input structure is what actually destroys it. A 10 kohm series resistor limits that current to a few milliamps at 35 V, which is inside the rating, and it also forms the input filter with the capacitance at the pin. Keep the two input resistors matched, since mismatch converts common mode into differential signal.
Millivolt signals on a 24 V rail
The input common-mode range includes the negative rail and goes below it, but the positive limit is around 1.5 V below the positive supply, so a signal riding at 24 V with a 36 V supply is inside the range while the same signal on a 24 V supply is not. That is the arithmetic that decides the supply rail in a 4 to 20 mA receiver: power the amplifier from 36 V, or level-shift the signal. Getting this wrong produces a channel that reads correctly at low currents and clips above 16 mA, which looks like a sensor fault rather than an amplifier limit.
350 microamps and the portable case
At 350 microamps typical and a 3 V supply the part dissipates about 1 mW, which is small enough for a battery instrument that samples every few seconds. The start-up time and the settling to the specified accuracy are what determine the average current, not the quiescent figure alone, so the duty cycle has to be measured rather than assumed. In the MSOP with no thermal pad the junction rise at 1 mW is negligible, which is another reason the small package is acceptable here: the part is not a heat source.
Availability and second sourcing
The gain equation, the input survival rating and the below-ground input range are the three parameters a substitute has to match; a part with a rail-to-rail input but no overvoltage survival will fail in the field where this one does not. The amplifier cross reference page groups the wide supply family, the pin to pin cross reference page lists the 8-lead outlines, and the lead time page shows which grades are available.