Contact Us

AD8223ARMZ

Brand: Analog Devices
Analog Devices AD8223ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8223ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8223ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8223ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8223ARMZ: Single-Supply Instrumentation Amplifier from 3 V to 24 V

The AD8223ARMZ is a low cost single-supply instrumentation amplifier that swings rail to rail on a 3 V to 24 V supply, or plus and minus 2 V to 12 V on a dual supply, and draws 500 microamps maximum. Gain is 5 plus 80 kohm divided by RG, so with no resistor fitted it is 5 and with a resistor it goes to 1000. Input bias current is 25 nA maximum, input noise is 30 nV per root hertz at 1 kHz referred to the input, the inputs work down to 150 mV below the negative rail, and the pinout follows the industry standard 8-lead arrangement, which is what makes it a direct replacement for older single-supply amplifiers in the same socket.

Published values

ParameterValue
Gain5 to 1000, G = 5 + 80 kohm divided by RG, gain of 5 with no resistor
Supply, single3 V to 24 V
Supply, dualplus and minus 2 V to 12 V
Supply current500 microamps maximum
Power at 3 V1.5 mW
Input bias current25 nA maximum
Input noise30 nV per root hertz at 1 kHz, referred to input
Input range150 mV below the negative rail
OutputRail to rail
PinoutIndustry standard 8-lead single-supply arrangement
Package8-lead SOIC and 8-lead MSOP

Thirty nanovolts per root hertz is a cost decision

At 30 nV per root hertz this part is roughly four times noisier than the precision instrumentation amplifiers in the same family, which sounds like a lot until the source impedance is taken into account. A 1 kohm source contributes 4 nV per root hertz of thermal noise, so the total is 30.3 nV and the amplifier dominates. A 10 kohm source contributes 12.7 nV and the total is 32.6 nV. Either way the amplifier sets the floor, so if the application needs 8 nV performance, this is the wrong part and the cost saving is not the issue. If it needs 30 nV, which covers most 12-bit systems and many 16-bit ones at reduced bandwidth, the part is adequate and the price is the reason to use it.

The 150 mV below the negative rail is not a rail-to-rail input

The input works to 150 mV below the negative supply, not to the positive one: the upper limit is roughly 1.5 V below the positive rail depending on gain. A single-supply bridge amplifier with the signal centred at half the rail is therefore fine, but a circuit that expects the input to reach the positive rail will clip. Check the common-mode range curve at the gain in use, because the range shrinks as gain rises. The output does go rail to rail, so a 3 V system can deliver almost the full 3 V swing, which is what makes the part usable at low supply voltages where headroom is scarce.

Gain of 5 with no resistor, and why that is useful

The gain equation has a fixed 5 in it, so the pins with no resistor give a clean gain of 5 with only the amplifier's own error. That is convenient for a 4 to 20 mA receiver or a bridge with a 20 mV full scale signal that has to reach 100 mV, and it removes one tolerance from the error budget. Above a gain of 5 the external resistor sets the rest, and its tolerance adds directly: a 1 percent resistor at a gain of 100 gives about 1 percent gain error. The 80 kohm internal resistor is trimmed, so with a 0.1 percent external part the gain error stays below 0.2 percent, which is usually enough for a 12-bit system.

Availability and second sourcing

The industry standard pinout is the useful part here: much of the older single-supply instrumentation amplifier stock shares it, so footprint compatibility is common even when the electrical performance differs. The parameters to compare are the gain equation, the common-mode range and the supply current. The amplifier cross reference page lists the single-supply family by gain range, the pin to pin cross reference page covers the 8-lead outlines, and the lead time page shows which parts are on the shelf.