AD8222ACPZ-R7
Product Specifications
AD8222ACPZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8222ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8222ACPZ-R7: Two Instrumentation Amplifiers in a 4 mm by 4 mm Package
The AD8222ACPZ-R7 is a dual channel precision instrumentation amplifier in a 4 mm by 4 mm LFCSP. Each channel has its own gain resistor, from 1 to 10,000, and its own reference pin, so two independent channels share a package and a supply but nothing else. Input noise is 8 nV per root hertz at 1 kHz with 0.25 microvolts peak to peak from 0.1 Hz to 10 Hz, the B grade holds 60 microvolts maximum offset and 0.3 microvolts per degree maximum drift, common-mode rejection is 126 dB minimum at a gain of 100, bandwidth is 140 kHz at that gain, and settling to 0.001 percent takes 13 microseconds. Both amplifiers together draw 2.2 mA maximum from a 2.3 V to 18 V supply.
Published values
| Parameter | Value |
|---|---|
| Channels | Two, independent gain and reference per channel |
| Gain | 1 to 10,000 per channel, G = 1 + 49.4 kohm divided by RG |
| Input noise | 8 nV per root hertz at 1 kHz |
| Low frequency noise | 0.25 microvolts peak to peak, 0.1 Hz to 10 Hz |
| Input offset, B grade | 60 microvolts maximum |
| Offset drift, B grade | 0.3 microvolts per degree Celsius maximum |
| Input bias current | 1.0 nA maximum |
| Common-mode rejection | 126 dB minimum at gain of 100, 80 dB minimum to 4 kHz at gain of 1 |
| Bandwidth | 140 kHz at gain of 100 |
| Settling | 13 microseconds to 0.001 percent |
| Supply | 2.3 V to 18 V, 2.2 mA maximum for both amplifiers |
| Package | 4 mm by 4 mm LFCSP, 16 leads |
Two channels in one package, and the crosstalk nobody specifies
Sharing a die means sharing a substrate, and the two channels are separated by the die, the lead frame and the package. Thermal crosstalk is the mechanism that matters at DC: a step on one channel heats the die locally and the other channel's offset moves by a fraction of a microvolt, recovering over a few seconds. For a multi-channel bridge measurement sampled slowly, that shows up as a slow wander after a large step, which is easy to mistake for a drifting sensor. The remedy is to keep the excitation and the large signals on separate channels, or to accept the settling time and discard readings for a few hundred milliseconds after a step. Two single parts on separate packages do not have this coupling, and that is the price of the board area saved.
Where 126 dB of common-mode rejection comes from
At a gain of 100, the differential signal is amplified before it reaches the stage that rejects the common mode, so the rejection improves with gain. The 126 dB figure is the B grade at that gain; at a gain of 1 the same part gives 80 dB to 4 kHz. This is why the gain resistor is not optional in a noisy environment: running the amplifier at unity gain to preserve dynamic range throws away most of the rejection it is capable of. Take the gain early and attenuate after, or use the differential output option on a single channel, which delivers the signal differentially and lets the converter do the subtraction.
Two references, two output offsets
Each channel has its own REF pin, so one channel can be referenced to mid-supply for a bipolar signal and the other to ground for a unipolar one. The reference pins are inputs to the output stage, so both must be low impedance: a divider alone will inject supply noise straight into the output. Bypass each with a capacitor close to the package and drive them from a buffer or a reference. The two references are independent, which means a mistake on one does not show up on the other, and a channel that reads a constant offset while its neighbour behaves is almost always a reference problem.
The 4 mm LFCSP and its thermal pad
The package has an exposed pad that must be soldered to a copper area, and the vias under it are the only thermal path. At 2.2 mA and 18 V the dissipation is 40 mW, which is small, but the die is small too and the two channels have to stay at the same temperature as each other for the drift specification to mean anything. Put the pad on a solid copper area with several vias, keep the gain resistors outside that area, and do not place the package next to a regulator. The 16-lead pitch is fine enough that solder paste stencil thickness matters more than the placement accuracy for yield.
Availability and second sourcing
A dual instrumentation amplifier is replaced either by two singles, which costs board area and loses the matched thermal environment, or by a dual with the same reference structure and gain equation. Both routes are viable, and the choice depends on whether the two channels are used as a pair or independently. The amplifier cross reference page groups the duals by gain range and package, the ADI part second source page separates the grades that match on noise and drift, and the lead time page shows which grades are shippable.