AD8221ARZ
Product Specifications
AD8221ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8221ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8221ARZ: The Same Precision Front End in an 8-Lead SOIC
The AD8221ARZ is the SOIC package of the AD8221 instrumentation amplifier. Electrically it is the same part: gain from 1 to 1000 set by one resistor through the relationship 1 plus 49.4 kohm divided by RG, a supply range of 2.3 V to 18 V, 8 nV per root hertz of input voltage noise, 0.25 microvolts peak to peak of low frequency noise, and 80 dB minimum common-mode rejection to 10 kHz at unity gain. What changes is the package: 8 leads on a 1.27 mm pitch instead of 0.65 mm, which is the difference between a board that can be assembled and inspected by hand and one that cannot, and a thermal path that spreads into more copper.
Published values
| Parameter | Value |
|---|---|
| Gain | 1 to 1000, one resistor, G = 1 + 49.4 kohm divided by RG |
| Supply range | 2.3 V to 18 V |
| Input noise | 8 nV per root hertz maximum at 1 kHz |
| Low frequency noise | 0.25 microvolts peak to peak, 0.1 Hz to 10 Hz |
| Common-mode rejection | 80 dB minimum to 10 kHz at gain of 1 |
| Bandwidth | 825 kHz at gain of 1 |
| Slew rate | 2 V per microsecond |
| Input offset, B grade | 25 microvolts maximum |
| Offset drift, B grade | 0.3 microvolts per degree Celsius maximum |
| Input bias current, B grade | 0.4 nA maximum |
| Specified temperature | minus 40 to plus 85 degrees Celsius, operational to 125 |
| Package | 8-lead SOIC, 1.27 mm pitch |
Why a 40 year old footprint still wins in some builds
An 8-lead SOIC can be placed and inspected with ordinary equipment, reworked with a hand iron, and routed on a two layer board with 0.2 mm traces without entering fine pitch territory. In low volume instruments, in equipment that has to be repairable in the field, and in boards that mix through hole and surface mount parts, that matters more than the board area saved by an MSOP. The SOIC also has a wider body, which spreads heat better: at a 15 V supply the die dissipates about 15 mW, and the wider package keeps the thermal gradient across the input pair smaller than the MSOP does. For a DC accuracy part that is a real advantage, not a cosmetic one.
What the input pair sees when the source is a bridge
A 350 ohm strain gauge bridge with a 5 V excitation delivers about 10 mV of full scale signal and has a source impedance of about 175 ohm in each leg. With 0.4 nA of bias current, the offset from that source is 70 nV, which is small against the 25 microvolt offset specification. The 8 nV of voltage noise over a 10 Hz bandwidth is 25 nV, so the noise floor is set by the amplifier and not by the bridge. This is the arithmetic that decides whether a precision instrumentation amplifier is needed at all: at a 350 ohm source, a good zero-drift op amp in a three amplifier configuration can match these numbers, and the instrumentation amplifier wins on component count and on common-mode range rather than on noise.
Supply decoupling and the reference pin
The reference pin sets the output offset and is a direct input to the output stage, so it has to be driven from a low impedance: a resistor divider alone will let supply noise into the output. Use a buffer, or a reference with a capacitor, and bypass it close to the pin. The supply pins need 0.1 microfarad ceramic plus 1 microfarad, and on a dual supply both rails, because the amplifier's common-mode rejection at high frequency depends on the supplies being low impedance at the frequencies where the rejection is falling. Keep the gain resistor close to the RG pins so the trace inductance does not sit inside the feedback loop.
Availability and second sourcing
Because the MSOP and SOIC variants share a die, a shortage in one package often has a same die answer in the other, and that is worth checking before looking at a different part. When a different part is needed, the noise, the offset drift and the gain equation are the three parameters to match. The amplifier cross reference page lists the grades by package, the pin to pin cross reference page covers the 8-lead outlines, and the lead time page shows what is on the shelf.